Daily Papers

We present FusionCore, an open-source ROS 2 sensor fusion package that fuses IMU, wheel encoder odometry, GPS, and Visual SLAM pose into a single 100 Hz odometry stream using a 23-state Unscented Kalman Filter (UKF). The 23rd state is an online estimate of the wheel encoder's systematic yaw rate bias, identified through GPS heading cross-covariance and subtracted during GPS blackouts to reduce heading drift in coast mode. FusionCore also estimates gyroscope and accelerometer biases as explicit filter states, handles GPS natively in ECEF without a separate coordinate projection node, applies per-sensor Mahalanobis chi-squared outlier gating calibrated to measurement degrees of freedom, and adapts sensor noise covariance automatically from the innovation sequence. VSLAM pose fusion enables GPS-denied operation with any visual odometry or SLAM system, including automatic recovery from map reinitialization. We evaluate against robot_localization on twelve full-length sequences (55-92 min each) from the NCLT public dataset. FusionCore achieves lower Absolute Trajectory Error (ATE) on ten of twelve sequences, with improvements ranging from 1.2x to 22.2x on winning sequences. The robot_localization UKF diverges numerically on all twelve sequences. FusionCore is available at https://github.com/manankharwar/fusioncore under the Apache 2.0 license.

In recent years there have been excellent results in Visual-Inertial Odometry techniques, which aim to compute the incremental motion of the sensor with high accuracy and robustness. However these approaches lack the capability to close loops, and trajectory estimation accumulates drift even if the sensor is continually revisiting the same place. In this work we present a novel tightly-coupled Visual-Inertial Simultaneous Localization and Mapping system that is able to close loops and reuse its map to achieve zero-drift localization in already mapped areas. While our approach can be applied to any camera configuration, we address here the most general problem of a monocular camera, with its well-known scale ambiguity. We also propose a novel IMU initialization method, which computes the scale, the gravity direction, the velocity, and gyroscope and accelerometer biases, in a few seconds with high accuracy. We test our system in the 11 sequences of a recent micro-aerial vehicle public dataset achieving a typical scale factor error of 1% and centimeter precision. We compare to the state-of-the-art in visual-inertial odometry in sequences with revisiting, proving the better accuracy of our method due to map reuse and no drift accumulation.

We present IF-D, a large-scale inertial dataset designed to enable self-supervised and foundational learning for IMU time series. IF-D comprises continuous, long-duration multichannel recordings (accelerometer, gyroscope, magnetometer) sampled at 200Hz using a UM7 IMU mounted inside a 3D-printed spherical enclosure that promotes diverse, free rotations during vehicle traversal. The collection spans approximately 135 minutes of recording, yielding around 1.6 million samples across nine sensor channels. We describe the data acquisition setup, preprocessing, and calibration procedures (six-orientation accelerometer calibration, stationary gyroscope bias estimation, and ellipsoid fitting for magnetometer hard-/soft-iron correction), and provide quantitative calibration results. IF-D is designed to mitigate platform specific motion bias and expose models to both physical dynamics and typical measurement noise, thereby facilitating robust representation learning and downstream tasks such as event detection, motion mode recognition, and inertial navigation.

Rapid urbanization and improved living standards have led to a substantial increase in the number of vehicles on the road, consequently resulting in a rise in the frequency of accidents. Among these accidents, motorbike accidents pose a particularly high risk, often resulting in serious injuries or deaths. A significant number of these fatalities occur due to delayed or inadequate medical attention. To this end, we propose a novel automatic detection and notification system specifically designed for motorbike accidents. The proposed system comprises two key components: a detection system and a physiological signal monitoring system. The detection system is integrated into the helmet and consists of a microcontroller, accelerometer, GPS, GSM, and Wi-Fi modules. The physio-monitoring system incorporates a sensor for monitoring pulse rate and SpO_{2} saturation. All collected data are presented on an LCD display and wirelessly transmitted to the detection system through the microcontroller of the physiological signal monitoring system. If the accelerometer readings consistently deviate from the specified threshold decided through extensive experimentation, the system identifies the event as an accident and transmits the victim's information -- including the GPS location, pulse rate, and SpO_{2} saturation rate -- to the designated emergency contacts. Preliminary results demonstrate the efficacy of the proposed system in accurately detecting motorbike accidents and promptly alerting emergency contacts. We firmly believe that the proposed system has the potential to significantly mitigate the risks associated with motorbike accidents and save lives.

With the increasing popularity of voice-based applications, acoustic eavesdropping has become a serious threat to users' privacy. While on smartphones the access to microphones needs an explicit user permission, acoustic eavesdropping attacks can rely on motion sensors (such as accelerometer and gyroscope), which access is unrestricted. However, previous instances of such attacks can only recognize a limited set of pre-trained words or phrases. In this paper, we present AccEar, an accelerometerbased acoustic eavesdropping attack that can reconstruct any audio played on the smartphone's loudspeaker with unconstrained vocabulary. We show that an attacker can employ a conditional Generative Adversarial Network (cGAN) to reconstruct highfidelity audio from low-frequency accelerometer signals. The presented cGAN model learns to recreate high-frequency components of the user's voice from low-frequency accelerometer signals through spectrogram enhancement. We assess the feasibility and effectiveness of AccEar attack in a thorough set of experiments using audio from 16 public personalities. As shown by the results in both objective and subjective evaluations, AccEar successfully reconstructs user speeches from accelerometer signals in different scenarios including varying sampling rate, audio volume, device model, etc.

Wearable motion sensing provides a continuous and scalable window into human behavior and health, making it a natural fit for foundation models, yet its pretraining and scaling principles remain poorly understood. Prior work studies isolated design choices, such as sensor placement or sampling frequency, often under fixed settings and narrow downstream tasks that fail to capture real-world sensing diversity. We introduce Inertia-1, a fully open exploration of wearable motion foundation models. Using massive corpora of accelerometer data from global sources spanning more than 18.2M hours, we build a controlled framework for studying the full lifecycle of wearable motion foundation models, covering data choices such as sensor modality, device placement, sampling rate, window length; model choices such as architectures and model size; and training choices such as pretraining objective and data scale. Extensive evaluations across 15 datasets spanning human activity recognition, freezing-of-gait detection, and disease prediction reveal intriguing findings for building motion foundation models that generalize across tasks and sensing conditions. Collectively, Inertia-1 not only presents state-of-the-art recipes for diverse downstream tasks, but also serves as a comprehensive, practical, and open cookbook for wearable motion representation learning.

This paper proposes a novel data-driven approach for inertial navigation, which learns to estimate trajectories of natural human motions just from an inertial measurement unit (IMU) in every smartphone. The key observation is that human motions are repetitive and consist of a few major modes (e.g., standing, walking, or turning). Our algorithm regresses a velocity vector from the history of linear accelerations and angular velocities, then corrects low-frequency bias in the linear accelerations, which are integrated twice to estimate positions. We have acquired training data with ground-truth motions across multiple human subjects and multiple phone placements (e.g., in a bag or a hand). The qualitatively and quantitatively evaluations have demonstrated that our algorithm has surprisingly shown comparable results to full Visual Inertial navigation. To our knowledge, this paper is the first to integrate sophisticated machine learning techniques with inertial navigation, potentially opening up a new line of research in the domain of data-driven inertial navigation. We will publicly share our code and data to facilitate further research.

We present a framework for gesture customization requiring minimal examples from users, all without degrading the performance of existing gesture sets. To achieve this, we first deployed a large-scale study (N=500+) to collect data and train an accelerometer-gyroscope recognition model with a cross-user accuracy of 95.7% and a false-positive rate of 0.6 per hour when tested on everyday non-gesture data. Next, we design a few-shot learning framework which derives a lightweight model from our pre-trained model, enabling knowledge transfer without performance degradation. We validate our approach through a user study (N=20) examining on-device customization from 12 new gestures, resulting in an average accuracy of 55.3%, 83.1%, and 87.2% on using one, three, or five shots when adding a new gesture, while maintaining the same recognition accuracy and false-positive rate from the pre-existing gesture set. We further evaluate the usability of our real-time implementation with a user experience study (N=20). Our results highlight the effectiveness, learnability, and usability of our customization framework. Our approach paves the way for a future where users are no longer bound to pre-existing gestures, freeing them to creatively introduce new gestures tailored to their preferences and abilities.

Recent trend of touch-screen devices produces an accessibility barrier for visually impaired people. On the other hand, these devices come with sensors such as accelerometer. This calls for new approaches to human computer interface (HCI). In this study, our aim is to find an alternative approach to classify 20 different hand gestures captured by iPhone 3GS's built-in accelerometer and make high accuracy on user-independent classifications using Dynamic Time Warping (DTW) with dynamic warping window sizes. 20 gestures with 1,100 gesture data are collected from 15 normal-visioned people. This data set is used for training. Experiment-1 based on this data set produced an accuracy rate of 96.7~\%. In order for visually impaired people to use the system, a gesture recognition based "talking" calculator is implemented. In Experiment-2, 4 visually impaired end-users used the calculator and obtained 95.5~\% accuracy rate among 17 gestures with 720 gesture data totally. Contributions of the techniques to the end result is also investigated. Dynamic warping window size is found to be the most effective one. The data and the code is available.

Respiratory acoustic foundation models (FMs) are benchmarked exclusively on smartphone recordings, yet clinical deployment increasingly targets body-coupled (BC) wearables whose sensors attenuate high-frequency content through tissue and bone, leaving FM reliability uncharacterised. We introduce BCoughBench, evaluating five FMs (OPERA-CT/CE/GT, HeAR, M2D+Resp) on nine classification tasks (AUROC, sensitivity at 95% specificity, Expected Calibration Error) and three age regression tasks (MAE vs. a mean-predictor baseline) across five EBEN-simulated BC sensor conditions on five labeled cough datasets. Mean AUROC declines from 0.785 (smartphone) to 0.689-0.723, degrading most under temple vibration pickup (Δ = -0.096) and least under the soft in-ear (Δ = -0.062). No FM meets the clinical sensitivity threshold (Se@Sp95 geq 0.20) on most disease tasks under any BC sensor. Sex classification on the CIDRZ cohort collapses (AUROC 0.954 to 0.596-0.628, Δ = -0.341) while COVID detection is nearly unaffected (Δ = -0.004). Age regression is robust, improving under the forehead accelerometer on CoughVID (MAE 9.61 to 8.97 yr); HeAR leads on regression and demographic tasks, M2D+Resp on disease and characteristic tasks. BCoughBench provides a reproducible framework for FM evaluation under wearable conditions.

Existing activity tracker datasets for human activity recognition are typically obtained by having participants perform predefined activities in an enclosed environment under supervision. This results in small datasets with a limited number of activities and heterogeneity, lacking the mixed and nuanced movements normally found in free-living scenarios. As such, models trained on laboratory-style datasets may not generalise out of sample. To address this problem, we introduce a new dataset involving wrist-worn accelerometers, wearable cameras, and sleep diaries, enabling data collection for over 24 hours in a free-living setting. The result is CAPTURE-24, a large activity tracker dataset collected in the wild from 151 participants, amounting to 3883 hours of accelerometer data, of which 2562 hours are annotated. CAPTURE-24 is two to three orders of magnitude larger than existing publicly available datasets, which is critical to developing accurate human activity recognition models.

As wearable and mobile devices become increasingly embedded in daily life, they offer a practical way to continuously sense human motion in the wild. But inertial signals are highly dependent on the sensing setup, including body location, mounting position, sensor orientation, device hardware, and sampling protocol. This setup dependence makes it difficult to learn motion representations that transfer across devices and datasets, and limits the broader use of wearable IMUs beyond closed-set recognition. We introduce AnyMo, a geometry-aware framework for setup-agnostic human motion modeling. AnyMo uses physics-grounded IMU simulation over dense body-surface placements to generate diverse and plausible synthetic signals, pre-trains a graph encoder from paired synthetic placement views and masked partial observations, tokenizes multi-position IMU into full-body motion tokens, and aligns these tokens with an LLM for motion-language understanding. We evaluate AnyMo on three complementary tasks: zero-shot activity recognition across 14 unseen downstream datasets, cross-modal retrieval, and wearable IMU motion captioning, where it improves average Accuracy/F1/R@2 by 11.7\%/11.6\%/22.6\% on HAR, increases zero-shot IMU-to-text and text-to-IMU retrieval MRR by 15.9\% and 28.6\%, respectively, and improves zero-shot captioning BERT-F1 by 18.8\%. These results support AnyMo as a generalist model for wearable motion understanding in the wild. Project page: https://baiyuchen.com/project/AnyMo.

Time Series Language Models (TSLMs) are emerging as unified models for reasoning over continuous signals in natural language. However, long-context retrieval remains a major limitation: existing models are typically trained and evaluated on short sequences, while real-world time-series sensor streams can span millions of datapoints. This mismatch requires precise temporal localization under strict computational constraints, a regime that is not captured by current benchmarks. We introduce TS-Haystack, a long-context temporal retrieval benchmark comprising ten task types across four categories: direct retrieval, temporal reasoning, multi-step reasoning and contextual anomaly. The benchmark uses controlled needle insertion by embedding short activity bouts into longer longitudinal accelerometer recordings, enabling systematic evaluation across context lengths ranging from seconds to 2 hours per sample. We hypothesize that existing TSLM time series encoders overlook temporal granularity as context length increases, creating a task-dependent effect: compression aids classification but impairs retrieval of localized events. Across multiple model and encoding strategies, we observe a consistent divergence between classification and retrieval behavior. Learned latent compression preserves or improves classification accuracy at compression ratios up to 176times, but retrieval performance degrades with context length, incurring in the loss of temporally localized information. These results highlight the importance of architectural designs that decouple sequence length from computational complexity while preserving temporal fidelity.

Event cameras are increasingly popular in robotics due to beneficial features such as low latency, energy efficiency, and high dynamic range. Nevertheless, their downstream task performance is greatly influenced by the optimization of bias parameters. These parameters, for instance, regulate the necessary change in light intensity to trigger an event, which in turn depends on factors such as the environment lighting and camera motion. This paper introduces feedback control algorithms that automatically tune the bias parameters through two interacting methods: 1) An immediate, on-the-fly fast adaptation of the refractory period, which sets the minimum interval between consecutive events, and 2) if the event rate exceeds the specified bounds even after changing the refractory period repeatedly, the controller adapts the pixel bandwidth and event thresholds, which stabilizes after a short period of noise events across all pixels (slow adaptation). Our evaluation focuses on the visual place recognition task, where incoming query images are compared to a given reference database. We conducted comprehensive evaluations of our algorithms' adaptive feedback control in real-time. To do so, we collected the QCR-Fast-and-Slow dataset that contains DAVIS346 event camera streams from 366 repeated traversals of a Scout Mini robot navigating through a 100 meter long indoor lab setting (totaling over 35km distance traveled) in varying brightness conditions with ground truth location information. Our proposed feedback controllers result in superior performance when compared to the standard bias settings and prior feedback control methods. Our findings also detail the impact of bias adjustments on task performance and feature ablation studies on the fast and slow adaptation mechanisms.

Structured tabular data dominates clinical medicine, yet existing benchmarks fail to reflect real-world properties like complex survey sampling, demographic oversampling, and subgroup fairness. We introduce the NHANES Accelerometry Cardiometabolic Benchmark, derived from NHANES 2003-2006, comprising 1,381 adults with hip-worn accelerometry, fasting laboratory biomarkers, dietary intake, and anthropometrics. We evaluate three tabular learning methods -- ridge regression, XGBoost, and the foundation model TabPFN v2 -- to predict glycated haemoglobin (HbA1c), fasting triglycerides, and C-reactive protein (CRP) from activity phenotypes and lifestyle covariates. TabPFN v2 achieves the best overall performance (HbA1c R^2=0.156, CRP R^2=0.383), while triglycerides remain largely unpredictable (R^2 < 0.05), consistent with known genetic dominance. We apply split conformal prediction to generate distribution-free 90% prediction intervals and evaluate demographic coverage equity across sex and race/ethnicity subgroups. Marginal coverage aligns with the 90% target for CRP and HbA1c but falls below for triglycerides. At the subgroup level, we observe localized undercoverage (e.g., HbA1c for Mexican American participants), illustrating the gap between marginal guarantees and the conditional coverage required for clinical fairness. Code and data are at https://github.com/felizzi/nhanes-accel-cardiometabolic-benchmark.

Inertial sensors play a pivotal role in indoor localization, which in turn lays the foundation for pervasive personal applications. However, low-cost inertial sensors, as commonly found in smartphones, are plagued by bias and noise, which leads to unbounded growth in error when accelerations are double integrated to obtain displacement. Small errors in state estimation propagate to make odometry virtually unusable in a matter of seconds. We propose to break the cycle of continuous integration, and instead segment inertial data into independent windows. The challenge becomes estimating the latent states of each window, such as velocity and orientation, as these are not directly observable from sensor data. We demonstrate how to formulate this as an optimization problem, and show how deep recurrent neural networks can yield highly accurate trajectories, outperforming state-of-the-art shallow techniques, on a wide range of tests and attachments. In particular, we demonstrate that IONet can generalize to estimate odometry for non-periodic motion, such as a shopping trolley or baby-stroller, an extremely challenging task for existing techniques.

Motion time series collected from mobile and wearable devices such as smartphones and smartwatches offer significant insights into human behavioral patterns, with wide applications in healthcare, automation, IoT, and AR/XR due to their low-power, always-on nature. However, given security and privacy concerns, building large-scale motion time series datasets remains difficult, preventing the development of pre-trained models for human activity analysis. Typically, existing models are trained and tested on the same dataset, leading to poor generalizability across variations in device location, device mounting orientation and human activity type. In this paper, we introduce UniMTS, the first unified pre-training procedure for motion time series that generalizes across diverse device latent factors and activities. Specifically, we employ a contrastive learning framework that aligns motion time series with text descriptions enriched by large language models. This helps the model learn the semantics of time series to generalize across activities. Given the absence of large-scale motion time series data, we derive and synthesize time series from existing motion skeleton data with all-joint coverage. Spatio-temporal graph networks are utilized to capture the relationships across joints for generalization across different device locations. We further design rotation-invariant augmentation to make the model agnostic to changes in device mounting orientations. Our model shows exceptional generalizability across 18 motion time series classification benchmark datasets, outperforming the best baselines by 340% in the zero-shot setting, 16.3% in the few-shot setting, and 9.2% in the full-shot setting.

Reasoning from sequences of raw sensory data is a ubiquitous problem across fields ranging from medical devices to robotics. These problems often involve using long sequences of raw sensor data (e.g. magnetometers, piezoresistors) to predict sequences of desirable physical quantities (e.g. force, inertial measurements). While classical approaches are powerful for locally-linear prediction problems, they often fall short when using real-world sensors. These sensors are typically non-linear, are affected by extraneous variables (e.g. vibration), and exhibit data-dependent drift. For many problems, the prediction task is exacerbated by small labeled datasets since obtaining ground-truth labels requires expensive equipment. In this work, we present Hierarchical State-Space Models (HiSS), a conceptually simple, new technique for continuous sequential prediction. HiSS stacks structured state-space models on top of each other to create a temporal hierarchy. Across six real-world sensor datasets, from tactile-based state prediction to accelerometer-based inertial measurement, HiSS outperforms state-of-the-art sequence models such as causal Transformers, LSTMs, S4, and Mamba by at least 23% on MSE. Our experiments further indicate that HiSS demonstrates efficient scaling to smaller datasets and is compatible with existing data-filtering techniques. Code, datasets and videos can be found on https://hiss-csp.github.io.

In personalized marketing, uplift models estimate incremental effects by modeling how customer behavior changes under alternative treatments. However, real-world data often exhibit biases - such as selection bias, spillover effects, and unobserved confounding - which adversely affect both estimation accuracy and metric validity. Despite the importance of bias-aware assessment, a lack of systematic studies persists. To bridge this gap, we design a systematic benchmarking framework. Unlike standard predictive tasks, real-world uplift datasets lack counterfactual ground truth, rendering direct metric validation infeasible. Therefore, a semi-synthetic approach serves as a critical enabler for systematic benchmarking, effectively bridging the gap by retaining real-world feature dependencies while providing the ground truth needed to isolate structural biases. Our investigations reveal that: (i) uplift targeting and prediction can manifest as distinct objectives, where proficiency in one does not ensure efficacy in the other; (ii) while many models exhibit inconsistent performance under diverse biases, TARNet shows notable robustness, providing insights for subsequent model design; (iii) evaluation metric stability is linked to mathematical alignment with the ATE, suggesting that ATE-approximating metrics yield more consistent model rankings under structural data imperfections. These findings suggest the need for more robust uplift models and metrics. Code will be released upon acceptance.

Full-stack autonomous driving perception modules usually consist of data-driven models based on multiple sensor modalities. However, these models might be biased to the sensor setup used for data acquisition. This bias can seriously impair the perception models' transferability to new sensor setups, which continuously occur due to the market's competitive nature. We envision sensor data abstraction as an interface between sensor data and machine learning applications for highly automated vehicles (HAD). For this purpose, we review the primary sensor modalities, camera, lidar, and radar, published in autonomous-driving related datasets, examine single sensor abstraction and abstraction of sensor setups, and identify critical paths towards an abstraction of sensor data from multiple perception configurations.

Diffusion Probabilistic Models have demonstrated remarkable performance across a wide range of generative tasks. However, we have observed that these models often suffer from a Signal-to-Noise Ratio-timestep (SNR-t) bias. This bias refers to the misalignment between the SNR of the denoising sample and its corresponding timestep during the inference phase. Specifically, during training, the SNR of a sample is strictly coupled with its timestep. However, this correspondence is disrupted during inference, leading to error accumulation and impairing the generation quality. We provide comprehensive empirical evidence and theoretical analysis to substantiate this phenomenon and propose a simple yet effective differential correction method to mitigate the SNR-t bias. Recognizing that diffusion models typically reconstruct low-frequency components before focusing on high-frequency details during the reverse denoising process, we decompose samples into various frequency components and apply differential correction to each component individually. Extensive experiments show that our approach significantly improves the generation quality of various diffusion models (IDDPM, ADM, DDIM, A-DPM, EA-DPM, EDM, PFGM++, and FLUX) on datasets of various resolutions with negligible computational overhead. The code is at https://github.com/AMAP-ML/DCW.

Temporally dense single-person "small data" have become widely available thanks to mobile apps and wearable sensors. Many caregivers and self-trackers want to use these data to help a specific person change their behavior to achieve desired health outcomes. Ideally, this involves discerning possible causes from correlations using that person's own observational time series data. In this paper, we estimate within-individual average treatment effects of physical activity on sleep duration, and vice-versa. We introduce the model twin randomization (MoTR; "motor") method for analyzing an individual's intensive longitudinal data. Formally, MoTR is an application of the g-formula (i.e., standardization, back-door adjustment) under serial interference. It estimates stable recurring effects, as is done in n-of-1 trials and single case experimental designs. We compare our approach to standard methods (with possible confounding) to show how to use causal inference to make better personalized recommendations for health behavior change, and analyze 222 days of Fitbit sleep and steps data for one of the authors.

Human Activity Recognition (HAR) plays a critical role in numerous applications, including healthcare monitoring, fitness tracking, and smart environments. Traditional deep learning (DL) approaches, while effective, often require extensive parameter tuning and may lack interpretability. In this work, we investigate the use of a single three-axis accelerometer and the Kolmogorov--Arnold Network (KAN) for HAR tasks, leveraging its ability to model complex nonlinear relationships with improved interpretability and parameter efficiency. The MotionSense dataset, containing smartphone-based motion sensor signals across various physical activities, is employed to evaluate the proposed approach. Our methodology involves preprocessing and normalization of accelerometer and gyroscope data, followed by KAN-based feature learning and classification. Experimental results demonstrate that the KAN achieves competitive or superior classification performance compared to conventional deep neural networks, while maintaining a significantly reduced parameter count. This highlights the potential of KAN architectures as an efficient and interpretable alternative for real-world HAR systems. The open-source implementation of the proposed framework is available at the Project's GitHub Repository.

Motion capture from a limited number of body-worn sensors, such as inertial measurement units (IMUs) and pressure insoles, has important applications in health, human performance, and entertainment. Recent work has focused on accurately reconstructing whole-body motion from a specific sensor configuration using six IMUs. While a common goal across applications is to use the minimal number of sensors to achieve required accuracy, the optimal arrangement of the sensors might differ from application to application. We propose a single diffusion model, DiffusionPoser, which reconstructs human motion in real-time from an arbitrary combination of sensors, including IMUs placed at specified locations, and, pressure insoles. Unlike existing methods, our model grants users the flexibility to determine the number and arrangement of sensors tailored to the specific activity of interest, without the need for retraining. A novel autoregressive inferencing scheme ensures real-time motion reconstruction that closely aligns with measured sensor signals. The generative nature of DiffusionPoser ensures realistic behavior, even for degrees-of-freedom not directly measured. Qualitative results can be found on our website: https://diffusionposer.github.io/.

Emotion prediction is the field of study to understand human emotions. Existing methods focus on modalities like text, audio, facial expressions, etc., which could be private to the user. Emotion can be derived from the subject's psychological data as well. Various approaches that employ combinations of physiological sensors for emotion recognition have been proposed. Yet, not all sensors are simple to use and handy for individuals in their daily lives. Thus, we propose a system to predict user emotion using smartwatch sensors. We design a framework to collect ground truth in real-time utilizing a mix of English and regional language-based videos to invoke emotions in participants and collect the data. Further, we modeled the problem as binary classification due to the limited dataset size and experimented with multiple machine-learning models. We also did an ablation study to understand the impact of features including Heart Rate, Accelerometer, and Gyroscope sensor data on mood. From the experimental results, Multi-Layer Perceptron has shown a maximum accuracy of 93.75 percent for pleasant-unpleasant (high/low valence classification) moods.

To enhance lifting-load estimation accuracy in industrial upper-limb assistive exoskeletons, this study proposes a machine learning-based approach using insole pressure sensors. Unlike traditional methods that rely on electromyography (EMG), force sensors, or posture data, insole pressure sensors provide a non-invasive, posture-independent, and stable solution suitable for long-term use. Lifting load data ranging from 2 to 10 kg (0.5 kg intervals) were collected from five subjects. Two data representations were investigated: channel-based vectors and map-based images. For the channel-based approach, conventional regression models (SVR, MLP, and Elastic Net) were trained on pooled data from all subjects to assess inter-subject generalization, specifically testing the ability to infer load levels unseen during training. In parallel, a preliminary feasibility study was conducted for the map-based deep learning model (MobileNetV2) using inner-subject data. Results indicate that the channel-based SVR achieved the most balanced accuracy and generalization performance, with a mean absolute error of 0.547 kg. These findings demonstrate the feasibility and advantages of using insole pressure data for variable load estimation, supporting control strategies in industrial exoskeleton applications.

This paper presents a motion data augmentation scheme incorporating motion synthesis encouraging diversity and motion correction imposing physical plausibility. This motion synthesis consists of our modified Variational AutoEncoder (VAE) and Inverse Kinematics (IK). In this VAE, our proposed sampling-near-samples method generates various valid motions even with insufficient training motion data. Our IK-based motion synthesis method allows us to generate a variety of motions semi-automatically. Since these two schemes generate unrealistic artifacts in the synthesized motions, our motion correction rectifies them. This motion correction scheme consists of imitation learning with physics simulation and subsequent motion debiasing. For this imitation learning, we propose the PD-residual force that significantly accelerates the training process. Furthermore, our motion debiasing successfully offsets the motion bias induced by imitation learning to maximize the effect of augmentation. As a result, our method outperforms previous noise-based motion augmentation methods by a large margin on both Recurrent Neural Network-based and Graph Convolutional Network-based human motion prediction models. The code is available at https://github.com/meaten/MotionAug.

Broader access to high-quality movement analysis could greatly benefit movement science and rehabilitation, such as allowing more detailed characterization of movement impairments and responses to interventions, or even enabling early detection of new neurological conditions or fall risk. While emerging technologies are making it easier to capture kinematics with biomechanical models, or how joint angles change over time, inferring the underlying physics that give rise to these movements, including ground reaction forces, joint torques, or even muscle activations, is still challenging. Here we explore whether imitation learning applied to a biomechanical model from a large dataset of movements from able-bodied and impaired individuals can learn to compute these inverse dynamics. Although imitation learning in human pose estimation has seen great interest in recent years, our work differences in several ways: we focus on using an accurate biomechanical model instead of models adopted for computer vision, we test it on a dataset that contains participants with impaired movements, we reported detailed tracking metrics relevant for the clinical measurement of movement including joint angles and ground contact events, and finally we apply imitation learning to a muscle-driven neuromusculoskeletal model. We show that our imitation learning policy, KinTwin, can accurately replicate the kinematics of a wide range of movements, including those with assistive devices or therapist assistance, and that it can infer clinically meaningful differences in joint torques and muscle activations. Our work demonstrates the potential for using imitation learning to enable high-quality movement analysis in clinical practice.

Strapdown inertial navigation systems are sensitive to the quality of the data provided by the accelerometer and gyroscope. Low-grade IMUs in handheld smart-devices pose a problem for inertial odometry on these devices. We propose a scheme for constraining the inertial odometry problem by complementing non-linear state estimation by a CNN-based deep-learning model for inferring the momentary speed based on a window of IMU samples. We show the feasibility of the model using a wide range of data from an iPhone, and present proof-of-concept results for how the model can be combined with an inertial navigation system for three-dimensional inertial navigation.

Wearable devices running Human Activity Recognition(HAR) on Inertial Measurement Units~(IMUs) waste energy by performing continuous classification for each window, even during long periods of unchanged activity. We address this with a lightweight change-detection gate: a non-parametric algorithm based on dynamic template matching that runs continuously at only approximately 16kFLOPs per step, requires no offline training, and does not need prior definition of target activity classes. The gate invokes the full HAR network only when it detects an activity change, reducing the computational load by over 67% in realistic monitoring settings. The algorithm is evaluated on smart glasses, smartwatch, and smartphone data, requiring only a brief device-specific calibration phase. The gate achieves 98% sensitivity on UCA-EHAR, ensuring no genuine activity transition is missed, while 75% specificity keeps unnecessary HAR invocations low. Results on WISDM are 97% sensitivity and 76% specificity, demonstrating robustness and flexibility to various settings.

This paper introduces a novel human pose estimation approach using sparse inertial sensors, addressing the shortcomings of previous methods reliant on synthetic data. It leverages a diverse array of real inertial motion capture data from different skeleton formats to improve motion diversity and model generalization. This method features two innovative components: a pseudo-velocity regression model for dynamic motion capture with inertial sensors, and a part-based model dividing the body and sensor data into three regions, each focusing on their unique characteristics. The approach demonstrates superior performance over state-of-the-art models across five public datasets, notably reducing pose error by 19\% on the DIP-IMU dataset, thus representing a significant improvement in inertial sensor-based human pose estimation. Our codes are available at {https://github.com/dx118/dynaip}.

Nowadays, Hearth Rate (HR) monitoring is a key feature of almost all wrist-worn devices exploiting photoplethysmography (PPG) sensors. However, arm movements affect the performance of PPG-based HR tracking. This issue is usually addressed by fusing the PPG signal with data produced by inertial measurement units. Thus, deep learning algorithms have been proposed, but they are considered too complex to deploy on wearable devices and lack the explainability of results. In this work, we present a new deep learning model, PULSE, which exploits temporal convolutions and multi-head cross-attention to improve sensor fusion's effectiveness and achieve a step towards explainability. We evaluate the performance of PULSE on three publicly available datasets, reducing the mean absolute error by 7.56% on the most extensive available dataset, PPG-DaLiA. Finally, we demonstrate the explainability of PULSE and the benefits of applying attention modules to PPG and motion data.

Inertial odometry is an attractive solution to the problem of state estimation for agile quadrotor flight. It is inexpensive, lightweight, and it is not affected by perceptual degradation. However, only relying on the integration of the inertial measurements for state estimation is infeasible. The errors and time-varying biases present in such measurements cause the accumulation of large drift in the pose estimates. Recently, inertial odometry has made significant progress in estimating the motion of pedestrians. State-of-the-art algorithms rely on learning a motion prior that is typical of humans but cannot be transferred to drones. In this work, we propose a learning-based odometry algorithm that uses an inertial measurement unit (IMU) as the only sensor modality for autonomous drone racing tasks. The core idea of our system is to couple a model-based filter, driven by the inertial measurements, with a learning-based module that has access to the thrust measurements. We show that our inertial odometry algorithm is superior to the state-of-the-art filter-based and optimization-based visual-inertial odometry as well as the state-of-the-art learned-inertial odometry in estimating the pose of an autonomous racing drone. Additionally, we show that our system is comparable to a visual-inertial odometry solution that uses a camera and exploits the known gate location and appearance. We believe that the application in autonomous drone racing paves the way for novel research in inertial odometry for agile quadrotor flight.

The rapid evolution of sensors and resource-efficient machine learning models has spurred the widespread adoption of wearable fitness tracking devices. Equipped with inertial sensors, such devices can continuously capture physical movements for fitness technology (FitTech), enabling applications from sports optimization to preventive healthcare. Traditional Centralized Learning approaches to detect fitness activities struggle with data privacy concerns, regulatory restrictions, and communication inefficiencies. In contrast, Federated Learning (FL) enables a decentralized model training by communicating model updates rather than potentially private wearable sensor data. Applying FL to FitTech presents unique challenges, such as data imbalance, lack of labeled data, heterogeneous user activities, and trade-offs between personalization and generalization. To simplify research on FitTech in FL, we present the FedFitTech baseline, under the Flower framework, which is publicly available and widely used by both industry and academic researchers. Additionally, to illustrate its usage, this paper presents a case study that implements a system based on the FedFitTech baseline, incorporating a client-side early stopping strategy and comparing the results. For instance, this system allows wearable devices to optimize the trade-off between capturing common fitness activities and preserving individuals' nuances, thereby enhancing both the scalability and efficiency of privacy-aware fitness tracking applications. The results show that this reduces the overall redundant communications by 13%, while maintaining the overall recognition performance at a negligible recognition cost by 1%. Thus, the FedFitTech baseline creates a foundation for a wide range of new research and development opportunities in FitTech, and it is available as open source at: https://github.com/shreyaskorde16/FedFitTech

We propose a computationally efficient inferential procedure for longitudinal function-on-function regression. The method follows a marginal three-step approach: (1) fit massive pointwise longitudinal scalar-on-function regression models, (2) smooth the resulting estimates along the bivariate functional domain, and (3) compute confidence bands using either an analytic approach for Gaussian data or a cluster bootstrap for Gaussian or non-Gaussian data. Simulation studies demonstrate that the proposed method achieves accurate estimation and valid inference, while substantially reducing computational burden compared to existing approaches. Methods are motivated by a physical activity intervention trial in older adults where high-dimensional wearable data were collected longitudinally across multiple visits. Our applications reveal significant increases in physical activity in the morning using interpersonal intervention strategies, but not intrapersonal strategies. The proposed methods are implemented in an R package.

In machine learning (ML), a widespread adage is that the area under the precision-recall curve (AUPRC) is a superior metric for model comparison to the area under the receiver operating characteristic (AUROC) for binary classification tasks with class imbalance. This paper challenges this notion through novel mathematical analysis, illustrating that AUROC and AUPRC can be concisely related in probabilistic terms. We demonstrate that AUPRC, contrary to popular belief, is not superior in cases of class imbalance and might even be a harmful metric, given its inclination to unduly favor model improvements in subpopulations with more frequent positive labels. This bias can inadvertently heighten algorithmic disparities. Prompted by these insights, a thorough review of existing ML literature was conducted, utilizing large language models to analyze over 1.5 million papers from arXiv. Our investigation focused on the prevalence and substantiation of the purported AUPRC superiority. The results expose a significant deficit in empirical backing and a trend of misattributions that have fuelled the widespread acceptance of AUPRC's supposed advantages. Our findings represent a dual contribution: a significant technical advancement in understanding metric behaviors and a stark warning about unchecked assumptions in the ML community. All experiments are accessible at https://github.com/mmcdermott/AUC_is_all_you_need.

Time series research has gathered lots of interests in the last decade, especially for Time Series Classification (TSC) and Time Series Forecasting (TSF). Research in TSC has greatly benefited from the University of California Riverside and University of East Anglia (UCR/UEA) Time Series Archives. On the other hand, the advancement in Time Series Forecasting relies on time series forecasting competitions such as the Makridakis competitions, NN3 and NN5 Neural Network competitions, and a few Kaggle competitions. Each year, thousands of papers proposing new algorithms for TSC and TSF have utilized these benchmarking archives. These algorithms are designed for these specific problems, but may not be useful for tasks such as predicting the heart rate of a person using photoplethysmogram (PPG) and accelerometer data. We refer to this problem as Time Series Extrinsic Regression (TSER), where we are interested in a more general methodology of predicting a single continuous value, from univariate or multivariate time series. This prediction can be from the same time series or not directly related to the predictor time series and does not necessarily need to be a future value or depend heavily on recent values. To the best of our knowledge, research into TSER has received much less attention in the time series research community and there are no models developed for general time series extrinsic regression problems. Most models are developed for a specific problem. Therefore, we aim to motivate and support the research into TSER by introducing the first TSER benchmarking archive. This archive contains 19 datasets from different domains, with varying number of dimensions, unequal length dimensions, and missing values. In this paper, we introduce the datasets in this archive and did an initial benchmark on existing models.

This paper presents a novel end-to-end deep learning framework for real-time inertial attitude estimation using 6DoF IMU measurements. Inertial Measurement Units are widely used in various applications, including engineering and medical sciences. However, traditional filters used for attitude estimation suffer from poor generalization over different motion patterns and environmental disturbances. To address this problem, we propose two deep learning models that incorporate accelerometer and gyroscope readings as inputs. These models are designed to be generalized to different motion patterns, sampling rates, and environmental disturbances. Our models consist of convolutional neural network layers combined with Bi-Directional Long-Short Term Memory followed by a Fully Forward Neural Network to estimate the quaternion. We evaluate the proposed method on seven publicly available datasets, totaling more than 120 hours and 200 kilometers of IMU measurements. Our results show that the proposed method outperforms state-of-the-art methods in terms of accuracy and robustness. Additionally, our framework demonstrates superior generalization over various motion characteristics and sensor sampling rates. Overall, this paper provides a comprehensive and reliable solution for real-time inertial attitude estimation using 6DoF IMUs, which has significant implications for a wide range of applications.

Automated exercise repetition counting has applications across the physical fitness realm, from personal health to rehabilitation. Motivated by the ubiquity of mobile phones and the benefits of tracking physical activity, this study explored the feasibility of counting exercise repetitions in real-time, using only on-device inference, on smartphones. In this work, after providing an extensive overview of the state-of-the-art automatic exercise repetition counting methods, we introduce a deep learning based exercise repetition counting system for smartphones consisting of five components: (1) Pose estimation, (2) Thresholding, (3) Optical flow, (4) State machine, and (5) Counter. The system is then implemented via a cross-platform mobile application named P\=uioio that uses only the smartphone camera to track repetitions in real time for three standard exercises: Squats, Push-ups, and Pull-ups. The proposed system was evaluated via a dataset of pre-recorded videos of individuals exercising as well as testing by subjects exercising in real time. Evaluation results indicated the system was 98.89% accurate in real-world tests and up to 98.85% when evaluated via the pre-recorded dataset. This makes it an effective, low-cost, and convenient alternative to existing solutions since the proposed system has minimal hardware requirements without requiring any wearable or specific sensors or network connectivity.

Mitigating bias in machine learning systems requires refining our understanding of bias propagation pathways: from societal structures to large-scale data to trained models to impact on society. In this work, we focus on one aspect of the problem, namely bias amplification: the tendency of models to amplify the biases present in the data they are trained on. A metric for measuring bias amplification was introduced in the seminal work by Zhao et al. (2017); however, as we demonstrate, this metric suffers from a number of shortcomings including conflating different types of bias amplification and failing to account for varying base rates of protected attributes. We introduce and analyze a new, decoupled metric for measuring bias amplification, BiasAmp_{rightarrow} (Directional Bias Amplification). We thoroughly analyze and discuss both the technical assumptions and normative implications of this metric. We provide suggestions about its measurement by cautioning against predicting sensitive attributes, encouraging the use of confidence intervals due to fluctuations in the fairness of models across runs, and discussing the limitations of what this metric captures. Throughout this paper, we work to provide an interrogative look at the technical measurement of bias amplification, guided by our normative ideas of what we want it to encompass. Code is located at https://github.com/princetonvisualai/directional-bias-amp

Tracking biosignals is crucial for monitoring wellness and preempting the development of severe medical conditions. Today, wearable devices can conveniently record various biosignals, creating the opportunity to monitor health status without disruption to one's daily routine. Despite widespread use of wearable devices and existing digital biomarkers, the absence of curated data with annotated medical labels hinders the development of new biomarkers to measure common health conditions. In fact, medical datasets are usually small in comparison to other domains, which is an obstacle for developing neural network models for biosignals. To address this challenge, we have employed self-supervised learning using the unlabeled sensor data collected under informed consent from the large longitudinal Apple Heart and Movement Study (AHMS) to train foundation models for two common biosignals: photoplethysmography (PPG) and electrocardiogram (ECG) recorded on Apple Watch. We curated PPG and ECG datasets from AHMS that include data from ~141K participants spanning ~3 years. Our self-supervised learning framework includes participant level positive pair selection, stochastic augmentation module and a regularized contrastive loss optimized with momentum training, and generalizes well to both PPG and ECG modalities. We show that the pre-trained foundation models readily encode information regarding participants' demographics and health conditions. To the best of our knowledge, this is the first study that builds foundation models using large-scale PPG and ECG data collected via wearable consumer devices x2013 prior works have commonly used smaller-size datasets collected in clinical and experimental settings. We believe PPG and ECG foundation models can enhance future wearable devices by reducing the reliance on labeled data and hold the potential to help the users improve their health.

Changes in body perception influence behavior and emotion and can be induced through multisensory feedback. Auditory feedback to one's actions can trigger such alterations; however, it is unclear which individual factors modulate these effects. We employ and evaluate SoniWeight Shoes, a wearable device based on literature for altering one's weight perception through manipulated footstep sounds. In a healthy population sample across a spectrum of individuals (n=84) with varying degrees of eating disorder symptomatology, physical activity levels, body concerns, and mental imagery capacities, we explore the effects of three sound conditions (low-frequency, high-frequency and control) on extensive body perception measures (demographic, behavioral, physiological, psychological, and subjective). Analyses revealed an impact of individual differences in each of these dimensions. Besides replicating previous findings, we reveal and highlight the role of individual differences in body perception, offering avenues for personalized sonification strategies. Datasets, technical refinements, and novel body map quantification tools are provided.

Increased effort during use of the paretic arm and hand can provoke involuntary abnormal synergy patterns and amplify stiffness effects of muscle tone for individuals after stroke, which can add difficulty for user-controlled devices to assist hand movement during functional tasks. We study how volitional effort, exerted in an attempt to open or close the hand, affects resistance to robot-assisted movement at the finger level. We perform experiments with three chronic stroke survivors to measure changes in stiffness when the user is actively exerting effort to activate ipsilateral EMG-controlled robot-assisted hand movements, compared with when the fingers are passively stretched, as well as overall effects from sustained active engagement and use. Our results suggest that active engagement of the upper extremity increases muscle tone in the finger to a much greater degree than through passive-stretch or sustained exertion over time. Potential design implications of this work suggest that developers should anticipate higher levels of finger stiffness when relying on user-driven ipsilateral control methods for assistive or rehabilitative devices for stroke.

There is a growing body of studies on applying deep learning to biometrics analysis. Certain circumstances, however, could impair the objective measures and accuracy of the proposed biometric data analysis methods. For instance, people with chronic pain (CP) unconsciously adapt specific body movements to protect themselves from injury or additional pain. Because there is no dedicated benchmark database to analyse this correlation, we considered one of the specific circumstances that potentially influence a person's biometrics during daily activities in this study and classified pain level and pain-related behaviour in the EmoPain database. To achieve this, we proposed a sparsely-connected recurrent neural networks (s-RNNs) ensemble with the gated recurrent unit (GRU) that incorporates multiple autoencoders using a shared training framework. This architecture is fed by multidimensional data collected from inertial measurement unit (IMU) and surface electromyography (sEMG) sensors. Furthermore, to compensate for variations in the temporal dimension that may not be perfectly represented in the latent space of s-RNNs, we fused hand-crafted features derived from information-theoretic approaches with represented features in the shared hidden state. We conducted several experiments which indicate that the proposed method outperforms the state-of-the-art approaches in classifying both pain level and pain-related behaviour.

Wearable sensors have become ubiquitous thanks to a variety of health tracking features. The resulting continuous and longitudinal measurements from everyday life generate large volumes of data; however, making sense of these observations for scientific and actionable insights is non-trivial. Inspired by the empirical success of generative modeling, where large neural networks learn powerful representations from vast amounts of text, image, video, or audio data, we investigate the scaling properties of sensor foundation models across compute, data, and model size. Using a dataset of up to 40 million hours of in-situ heart rate, heart rate variability, electrodermal activity, accelerometer, skin temperature, and altimeter per-minute data from over 165,000 people, we create LSM, a multimodal foundation model built on the largest wearable-signals dataset with the most extensive range of sensor modalities to date. Our results establish the scaling laws of LSM for tasks such as imputation, interpolation and extrapolation, both across time and sensor modalities. Moreover, we highlight how LSM enables sample-efficient downstream learning for tasks like exercise and activity recognition.

Understanding biases and stereotypes encoded in the weights of Large Language Models (LLMs) is crucial for developing effective mitigation strategies. Biased behaviour is often subtle and non-trivial to isolate, even when deliberately elicited, making systematic analysis and debiasing particularly challenging. To address this, we introduce BiasGym, a simple, cost-effective, and generalizable framework for reliably injecting, analyzing, and mitigating conceptual associations within LLMs. BiasGym consists of two components: BiasInject, which injects specific biases into the model via token-based fine-tuning while keeping the model frozen, and BiasScope, which leverages these injected signals to identify and steer the components responsible for biased behavior. Our method enables consistent bias elicitation for mechanistic analysis, supports targeted debiasing without degrading performance on downstream tasks, and generalizes to biases unseen during training. We demonstrate the effectiveness of BiasGym in reducing real-world stereotypes (e.g., people from a country being `reckless drivers') and in probing fictional associations (e.g., people from a country having `blue skin'), showing its utility for both safety interventions and interpretability research.

Study Objectives: We investigate a Mamba-based deep learning approach for sleep staging on signals from ANNE One (Sibel Health, Evanston, IL), a non-intrusive dual-module wireless wearable system measuring chest electrocardiography (ECG), triaxial accelerometry, and chest temperature, and finger photoplethysmography and finger temperature. Methods: We obtained wearable sensor recordings from 357 adults undergoing concurrent polysomnography (PSG) at a tertiary care sleep lab. Each PSG recording was manually scored and these annotations served as ground truth labels for training and evaluation of our models. PSG and wearable sensor data were automatically aligned using their ECG channels with manual confirmation by visual inspection. We trained a Mamba-based recurrent neural network architecture on these recordings. Ensembling of model variants with similar architectures was performed. Results: After ensembling, the model attains a 3-class (wake, non rapid eye movement [NREM] sleep, rapid eye movement [REM] sleep) balanced accuracy of 84.02%, F1 score of 84.23%, Cohen's κ of 72.89%, and a Matthews correlation coefficient (MCC) score of 73.00%; a 4-class (wake, light NREM [N1/N2], deep NREM [N3], REM) balanced accuracy of 75.30%, F1 score of 74.10%, Cohen's κ of 61.51%, and MCC score of 61.95%; a 5-class (wake, N1, N2, N3, REM) balanced accuracy of 65.11%, F1 score of 66.15%, Cohen's κ of 53.23%, MCC score of 54.38%. Conclusions: Our Mamba-based deep learning model can successfully infer major sleep stages from the ANNE One, a wearable system without electroencephalography (EEG), and can be applied to data from adults attending a tertiary care sleep clinic.

The coupling of the angular jitter of the spacecraft and their sub-assemblies with the optical bench and the telescope into the interferometric length readout will be a major noise source in the LISA mission. We refer to this noise as tilt-to-length (TTL) coupling. It will be reduced directly by realignments, and the residual noise will then be subtracted in post-processing. The success of these mitigation strategies depends on an accurate computation of the TTL coupling coefficients. We present here a thorough analysis of the accuracy of the coefficient estimation under different jitter characteristics, angular readout noise levels, and gravitational wave sources. We analyze in which cases the estimates degrade using two estimators, the common least squares estimator and the instrumental variables estimator. Our investigations show that angular readout noise leads to a bias of the least squares estimator, depending on the TTL coupling coefficients, jitter and readout noise level, while the instrumental variable estimator is not biased. We present an equation that predicts the estimation bias of the least squares method due to angular readout noise.

Introduction: Data from wearable devices collected in free-living settings, and labelled with physical activity behaviours compatible with health research, are essential for both validating existing wearable-based measurement approaches and developing novel machine learning approaches. One common way of obtaining these labels relies on laborious annotation of sequences of images captured by cameras worn by participants through the course of a day. Methods: We compare the performance of three vision language models and two discriminative models on two free-living validation studies with 161 and 111 participants, collected in Oxfordshire, United Kingdom and Sichuan, China, respectively, using the Autographer (OMG Life, defunct) wearable camera. Results: We found that the best open-source vision-language model (VLM) and fine-tuned discriminative model (DM) achieved comparable performance when predicting sedentary behaviour from single images on unseen participants in the Oxfordshire study; median F1-scores: VLM = 0.89 (0.84, 0.92), DM = 0.91 (0.86, 0.95). Performance declined for light (VLM = 0.60 (0.56,0.67), DM = 0.70 (0.63, 0.79)), and moderate-to-vigorous intensity physical activity (VLM = 0.66 (0.53, 0.85); DM = 0.72 (0.58, 0.84)). When applied to the external Sichuan study, performance fell across all intensity categories, with median Cohen's kappa-scores falling from 0.54 (0.49, 0.64) to 0.26 (0.15, 0.37) for the VLM, and from 0.67 (0.60, 0.74) to 0.19 (0.10, 0.30) for the DM. Conclusion: Freely available computer vision models could help annotate sedentary behaviour, typically the most prevalent activity of daily living, from wearable camera images within similar populations to seen data, reducing the annotation burden.

It stands to reason that the amount and the quality of data is of key importance for setting up accurate AI-driven models. Among others, a fundamental aspect to consider is the bias introduced during sample selection in database generation. This is particularly relevant when a model is trained on a specialized dataset to predict a property of interest, and then applied to forecast the same property over samples having a completely different genesis. Indeed, the resulting biased model will likely produce unreliable predictions for many of those out-of-the-box samples. Neglecting such an aspect may hinder the AI-based discovery process, even when high quality, sufficiently large and highly reputable data sources are available. In this regard, with superconducting and thermoelectric materials as two prototypical case studies in the field of energy material discovery, we present and validate a new method (based on a classification strategy) capable of detecting, quantifying and circumventing the presence of cross-domain data bias.

Compared with visual signals, Inertial Measurement Units (IMUs) placed on human limbs can capture accurate motion signals while being robust to lighting variation and occlusion. While these characteristics are intuitively valuable to help egocentric action recognition, the potential of IMUs remains under-explored. In this work, we present a novel method for action recognition that integrates motion data from body-worn IMUs with egocentric video. Due to the scarcity of labeled multimodal data, we design an MAE-based self-supervised pretraining method, obtaining strong multi-modal representations via modeling the natural correlation between visual and motion signals. To model the complex relation of multiple IMU devices placed across the body, we exploit the collaborative dynamics in multiple IMU devices and propose to embed the relative motion features of human joints into a graph structure. Experiments show our method can achieve state-of-the-art performance on multiple public datasets. The effectiveness of our MAE-based pretraining and graph-based IMU modeling are further validated by experiments in more challenging scenarios, including partially missing IMU devices and video quality corruption, promoting more flexible usages in the real world.

This paper addresses a regression problem in which output label values are the results of sensing the magnitude of a phenomenon. A low value of such labels can mean either that the actual magnitude of the phenomenon was low or that the sensor made an incomplete observation. This leads to a bias toward lower values in labels and the resultant learning because labels may have lower values due to incomplete observations, even if the actual magnitude of the phenomenon was high. Moreover, because an incomplete observation does not provide any tags indicating incompleteness, we cannot eliminate or impute them. To address this issue, we propose a learning algorithm that explicitly models incomplete observations corrupted with an asymmetric noise that always has a negative value. We show that our algorithm is unbiased as if it were learned from uncorrupted data that does not involve incomplete observations. We demonstrate the advantages of our algorithm through numerical experiments.

Foundation models, a cornerstone of recent advancements in machine learning, have predominantly thrived on complete and well-structured data. Wearable sensor data frequently suffers from significant missingness, posing a substantial challenge for self-supervised learning (SSL) models that typically assume complete data inputs. This paper introduces the second generation of Large Sensor Model (LSM-2) with Adaptive and Inherited Masking (AIM), a novel SSL approach that learns robust representations directly from incomplete data without requiring explicit imputation. AIM's core novelty lies in its use of learnable mask tokens to model both existing ("inherited") and artificially introduced missingness, enabling it to robustly handle fragmented real-world data during inference. Pre-trained on an extensive dataset of 40M hours of day-long multimodal sensor data, our LSM-2 with AIM achieves the best performance across a diverse range of tasks, including classification, regression and generative modeling. Furthermore, LSM-2 with AIM exhibits superior scaling performance, and critically, maintains high performance even under targeted missingness scenarios, reflecting clinically coherent patterns, such as the diagnostic value of nighttime biosignals for hypertension prediction. This makes AIM a more reliable choice for real-world wearable data applications.

Many political science theories relate to latent variables, but such quantities cannot be observed directly and must instead be estimated from data with inherent uncertainty. In regression models, when a variable is measured with error, its slope coefficient is known to be biased toward zero. We show how measurement error interacts with unique aspects of latent variable estimation, identification restrictions in particular, and demonstrate how common error adjustment strategies can worsen bias. We introduce a method for adjusting coefficients on latent predictors, which reduces bias and typically increases the magnitude of estimated coefficients, often dramatically. We illustrate these dynamics using several different estimation strategies for the latent predictors. Corrected estimates using our proposed method show stronger relationships -- sometimes up to 50% larger -- than those from naive regression. Our findings highlight the importance of considering measurement error in latent predictors and the inadequacy of many commonly used approaches for dealing with this issue.

Human Activity Recognition (HAR) based on wearable inertial sensors plays a critical role in remote health monitoring. In patients with movement disorders, the ability to detect abnormal patient movements in their home environments can enable continuous optimization of treatments and help alert caretakers as needed. Machine learning approaches have been proposed for HAR tasks using Inertial Measurement Unit (IMU) data; however, most rely on application-specific labels and lack generalizability to data collected in different environments or populations. To address this limitation, we propose a new cross-modal self-supervised pretraining approach to learn representations from large-sale unlabeled IMU-video data and demonstrate improved generalizability in HAR tasks on out of distribution (OOD) IMU datasets, including a dataset collected from patients with Parkinson's disease. Specifically, our results indicate that the proposed cross-modal pretraining approach outperforms the current state-of-the-art IMU-video pretraining approach and IMU-only pretraining under zero-shot and few-shot evaluations. Broadly, our study provides evidence that in highly dynamic data modalities, such as IMU signals, cross-modal pretraining may be a useful tool to learn generalizable data representations. Our software is available at https://github.com/scheshmi/IMU-Video-OOD-HAR.

We introduce a novel method for measuring properties of periodic phenomena with an event camera, a device asynchronously reporting brightness changes at independently operating pixels. The approach assumes that for fast periodic phenomena, in any spatial window where it occurs, a very similar set of events is generated at the time difference corresponding to the frequency of the motion. To estimate the frequency, we compute correlations of spatio-temporal windows in the event space. The period is calculated from the time differences between the peaks of the correlation responses. The method is contactless, eliminating the need for markers, and does not need distinguishable landmarks. We evaluate the proposed method on three instances of periodic phenomena: (i) light flashes, (ii) vibration, and (iii) rotational speed. In all experiments, our method achieves a relative error lower than 0.04%, which is within the error margin of ground truth measurements.

End-to-end driving systems have recently made rapid progress, in particular on CARLA. Independent of their major contribution, they introduce changes to minor system components. Consequently, the source of improvements is unclear. We identify two biases that recur in nearly all state-of-the-art methods and are critical for the observed progress on CARLA: (1) lateral recovery via a strong inductive bias towards target point following, and (2) longitudinal averaging of multimodal waypoint predictions for slowing down. We investigate the drawbacks of these biases and identify principled alternatives. By incorporating our insights, we develop TF++, a simple end-to-end method that ranks first on the Longest6 and LAV benchmarks, gaining 14 driving score over the best prior work on Longest6.

Time-series foundation models excel at tasks like forecasting across diverse data types by leveraging informative waveform representations. Wearable sensing data, however, pose unique challenges due to their variability in patterns and frequency bands, especially for healthcare-related outcomes. The main obstacle lies in crafting generalizable representations that adapt efficiently across heterogeneous sensing configurations and applications. To address this, we propose NormWear, the first multi-modal and ubiquitous foundation model designed to extract generalized and informative representations from wearable sensing data. Specifically, we design a channel-aware attention mechanism with a shared special liaison [CLS] token to detect signal patterns in both intra-sensor and inter-sensors. This helps the model to extract more meaningful information considering both time series themselves and the relationships between input sensors. This helps the model to be widely compatible with various sensors settings. NormWear is pretrained on a diverse set of physiological signals, including PPG, ECG, EEG, GSR, and IMU, from various public datasets. Our model shows exceptional generalizability across 11 public wearable sensing datasets, spanning 18 applications in mental health, body state inference, vital sign estimation, and disease risk evaluation. It consistently outperforms competitive baselines under zero-shot, partial-shot, and full-shot settings, indicating broad applicability in real-world health applications.

This paper sets a new foundation for data-driven inertial navigation research, where the task is the estimation of positions and orientations of a moving subject from a sequence of IMU sensor measurements. More concretely, the paper presents 1) a new benchmark containing more than 40 hours of IMU sensor data from 100 human subjects with ground-truth 3D trajectories under natural human motions; 2) novel neural inertial navigation architectures, making significant improvements for challenging motion cases; and 3) qualitative and quantitative evaluations of the competing methods over three inertial navigation benchmarks. We will share the code and data to promote further research.

Several popular computer vision (CV) datasets, specifically employed for Object Detection (OD) in autonomous driving tasks exhibit biases due to a range of factors including weather and lighting conditions. These biases may impair a model's generalizability, rendering it ineffective for OD in novel and unseen datasets. Especially, in autonomous driving, it may prove extremely high risk and unsafe for the vehicle and its surroundings. This work focuses on understanding these datasets better by identifying such "good-weather" bias. Methods to mitigate such bias which allows the OD models to perform better and improve the robustness are also demonstrated. A simple yet effective OD framework for studying bias mitigation is proposed. Using this framework, the performance on popular datasets is analyzed and a significant difference in model performance is observed. Additionally, a knowledge transfer technique and a synthetic image corruption technique are proposed to mitigate the identified bias. Finally, using the DAWN dataset, the findings are validated on the OD task, demonstrating the effectiveness of our techniques in mitigating real-world "good-weather" bias. The experiments show that the proposed techniques outperform baseline methods by averaged fourfold improvement.

This paper addresses the task of counting human actions of interest using sensor data from wearable devices. We propose a novel exemplar-based framework, allowing users to provide exemplars of the actions they want to count by vocalizing predefined sounds ''one'', ''two'', and ''three''. Our method first localizes temporal positions of these utterances from the audio sequence. These positions serve as the basis for identifying exemplars representing the action class of interest. A similarity map is then computed between the exemplars and the entire sensor data sequence, which is further fed into a density estimation module to generate a sequence of estimated density values. Summing these density values provides the final count. To develop and evaluate our approach, we introduce a diverse and realistic dataset consisting of real-world data from 37 subjects and 50 action categories, encompassing both sensor and audio data. The experiments on this dataset demonstrate the viability of the proposed method in counting instances of actions from new classes and subjects that were not part of the training data. On average, the discrepancy between the predicted count and the ground truth value is 7.47, significantly lower than the errors of the frequency-based and transformer-based methods. Our project, code and dataset can be found at https://github.com/cvlab-stonybrook/ExRAC.

Emergent misalignment (EM) occurs when narrow finetuning causes a model to behave dangerously outside the finetuning task. Standard training signals can miss this shift, making reliable detection costly if it depends on repeated behavioral evaluation. We ask whether emergent misalignment can instead be detected from internal representations during finetuning. Using seven alignment-relevant traits encoded as linear directions in activation space, we track representational drift across training checkpoints in four open-source 7-9B LLMs. EM-relevant drift concentrates on a low-dimensional axis that explains 65.5% of the variance, revealing a geometric signature in the studied regime. A low-overhead monitor built on this drift profile detects dangerous checkpoints with 2.2% false negative rate, 2.9% false positive rate, and 0.990 AUROC on held-out perturbation types, outperforming unsupervised PCA and SAE baselines. Stress tests on two 14B models, longer finetuning runs, and misaligned starting points identify key deployment boundaries. These results position trait-space monitoring as a practical complement to behavioral evaluation for EM detection during LoRA-based finetuning, while showing that deployment across substantially different regimes may require recalibration.

This paper introduces a novel method for real-time exercise classification using a Bidirectional Long Short-Term Memory (BiLSTM) neural network. Existing exercise recognition approaches often rely on synthetic datasets, raw coordinate inputs sensitive to user and camera variations, and fail to fully exploit the temporal dependencies in exercise movements. These issues limit their generalizability and robustness in real-world conditions, where lighting, camera angles, and user body types vary. To address these challenges, we propose a BiLSTM-based model that leverages invariant features, such as joint angles, alongside raw coordinates. By using both angles and (x, y, z) coordinates, the model adapts to changes in perspective, user positioning, and body differences, improving generalization. Training on 30-frame sequences enables the BiLSTM to capture the temporal context of exercises and recognize patterns evolving over time. We compiled a dataset combining synthetic data from the InfiniteRep dataset and real-world videos from Kaggle and other sources. This dataset includes four common exercises: squat, push-up, shoulder press, and bicep curl. The model was trained and validated on these diverse datasets, achieving an accuracy of over 99% on the test set. To assess generalizability, the model was tested on 2 separate test sets representative of typical usage conditions. Comparisons with the previous approach from the literature are present in the result section showing that the proposed model is the best-performing one. The classifier is integrated into a web application providing real-time exercise classification and repetition counting without manual exercise selection. Demo and datasets are available at the following GitHub Repository: https://github.com/RiccardoRiccio/Fitness-AI-Trainer-With-Automatic-Exercise-Recognition-and-Counting.

Human motion generation holds significant promise in fields such as animation, film production, and robotics. However, existing methods often fail to produce physically plausible movements that adhere to biomechanical principles. While recent autoregressive and diffusion models have improved visual quality, they frequently overlook essential biodynamic features, such as muscle activation patterns and joint coordination, leading to motions that either violate physical laws or lack controllability. This paper introduces BioMoDiffuse, a novel biomechanics-aware diffusion framework that addresses these limitations. It features three key innovations: (1) A lightweight biodynamic network that integrates muscle electromyography (EMG) signals and kinematic features with acceleration constraints, (2) A physics-guided diffusion process that incorporates real-time biomechanical verification via modified Euler-Lagrange equations, and (3) A decoupled control mechanism that allows independent regulation of motion speed and semantic context. We also propose a set of comprehensive evaluation protocols that combines traditional metrics (FID, R-precision, etc.) with new biomechanical criteria (smoothness, foot sliding, floating, etc.). Our approach bridges the gap between data-driven motion synthesis and biomechanical authenticity, establishing new benchmarks for physically accurate motion generation.

Smartphones and smartwatches are ever-present in daily life, and provide a rich source of information on their users' behaviour. In particular, digital traces derived from the phone's embedded movement sensors present an opportunity for a forensic investigator to gain insight into a person's physical activities. In this work, we present a machine learning-based approach to translate digital traces into likelihood ratios (LRs) for different types of physical activities. Evaluating on a new dataset, NFI\_FARED, which contains digital traces from four different types of iPhones labelled with 19 activities, it was found that our approach could produce useful LR systems to distinguish 167 out of a possible 171 activity pairings. The same approach was extended to analyse likelihoods for multiple activities (or groups of activities) simultaneously and create activity timelines to aid in both the early and latter stages of forensic investigations. The dataset and all code required to replicate the results have also been made public to encourage further research on this topic.

An invariant extended Kalman filter (IEKF) is developed for state estimation of serial rigid manipulators with an arbitrary number of links, formulated entirely within the Lie group SE(3). The group-affine property of the kinematic equations makes the linearised error dynamics autonomous, so the Riccati equation governs the true error covariance rather than a local approximation. A physically separated noise model treats gyroscope and accelerometer channels independently: the accelerometer provides translational twist via gravity-compensated integration, yielding a measurement covariance that scales with the sample interval in exact analogy with process noise discretisation; a state-dependent Coriolis noise term captures gyroscope noise propagating through the nonlinear dynamics, vanishing at rest and growing with twist magnitude. The filter is structured as a modular chain of per-link IEKFs in which the predicted covariance of each link depends on its predecessor only through the Adjoint-transformed posterior, giving linear computational cost in link count. Exponential ultimate boundedness in mean square is established via a Lie algebra Lyapunov function, with per-link bounds chained through the Adjoint operator norm to yield a stability certificate that is modular and scalable to arbitrary chain length. Numerical results validate the design.

Recent research has demonstrated the capability of behavior signals captured by smartphones and wearables for longitudinal behavior modeling. However, there is a lack of a comprehensive public dataset that serves as an open testbed for fair comparison among algorithms. Moreover, prior studies mainly evaluate algorithms using data from a single population within a short period, without measuring the cross-dataset generalizability of these algorithms. We present the first multi-year passive sensing datasets, containing over 700 user-years and 497 unique users' data collected from mobile and wearable sensors, together with a wide range of well-being metrics. Our datasets can support multiple cross-dataset evaluations of behavior modeling algorithms' generalizability across different users and years. As a starting point, we provide the benchmark results of 18 algorithms on the task of depression detection. Our results indicate that both prior depression detection algorithms and domain generalization techniques show potential but need further research to achieve adequate cross-dataset generalizability. We envision our multi-year datasets can support the ML community in developing generalizable longitudinal behavior modeling algorithms.

Motor impairments, including tremor, bradykinesia, gait abnormalities, and postural instability, are common across many neurological and movement-related conditions. Conventional clinical assessments are often intermittent and may fail to capture subtle temporal variations in motor behavior. While wearable IMUs and third-person video have shown promise for objective motor assessment, third-person recordings raise privacy concerns and require constrained acquisition setups. In contrast, egocentric vision provides a more naturalistic and privacyaware alternative. In this work, we introduce EgoInertia-MI, a multimodal benchmark dataset combining synchronized egocentric video and wearable IMU signals for motor impairment analysis. The dataset contains 19 upper- and lower-body activities performed by healthy volunteers simulating varying levels of motor impairment severity levels: no impairment, mild impairment, and severe impairment. We establish two benchmark tasks: action recognition and motor impairment severity estimation, and evaluate multiple unimodal and multimodal baselines. Experimental results show that egocentric video provides strong cues for motor impairment assessment, while multimodal fusion achieves the best overall performance, reaching 0.78 Macro-F1 for severity estimation and 0.93 Macro-F1 for action recognition. These findings highlight the potential of combining egocentric vision and wearable sensing for ecologically valid and privacy-aware motor assessment. Code and data are available at:https://fatemah-alh.github.io/EgoInertia-MI-Page/.

This paper presents our solution for the Elderly Action Recognition (EAR) Challenge, part of the Computer Vision for Smalls Workshop at WACV 2025. The competition focuses on recognizing Activities of Daily Living (ADLs) performed by the elderly, covering six action categories with a diverse dataset. Our approach builds upon a state-of-the-art action recognition model, fine-tuned through transfer learning on elderly-specific datasets to enhance adaptability. To improve generalization and mitigate dataset bias, we carefully curated training data from multiple publicly available sources and applied targeted pre-processing techniques. Our solution currently achieves 0.81455 accuracy on the public leaderboard, highlighting its effectiveness in classifying elderly activities. Source codes are publicly available at https://github.com/ffyyytt/EAR-WACV25-DAKiet-TSM.

To increase the availability and adoption of the soundscape standard, a low-cost calibration procedure for reproduction of audio stimuli over headphones was proposed as part of the global ``Soundscape Attributes Translation Project'' (SATP) for validating ISO/TS~12913-2:2018 perceived affective quality (PAQ) attribute translations. A previous preliminary study revealed significant deviations from the intended equivalent continuous A-weighted sound pressure levels (L_{A,eq}) using the open-circuit voltage (OCV) calibration procedure. For a more holistic human-centric perspective, the OCV method is further investigated here in terms of psychoacoustic parameters, including relevant exceedance levels to account for temporal effects on the same 27 stimuli from the SATP. Moreover, a within-subjects experiment with 36 participants was conducted to examine the effects of OCV calibration on the PAQ attributes in ISO/TS~12913-2:2018. Bland-Altman analysis of the objective indicators revealed large biases in the OCV method across all weighted sound level and loudness indicators; and roughness indicators at 5{\%} and 10{\%} exceedance levels. Significant perceptual differences due to the OCV method were observed in about 20{\%} of the stimuli, which did not correspond clearly with the biased acoustic indicators. A cautioned interpretation of the objective and perceptual differences due to small and unpaired samples nevertheless provide grounds for further investigation.

As large language models transition from text-based interfaces to audio interactions in clinical settings, they might introduce new vulnerabilities through paralinguistic cues in audio. We evaluated these models on 170 clinical cases, each synthesized into speech from 36 distinct voice profiles spanning variations in age, gender, and emotion. Our findings reveal a severe modality bias: surgical recommendations for audio inputs varied by as much as 35% compared to identical text-based inputs, with one model providing 80% fewer recommendations. Further analysis uncovered age disparities of up to 12% between young and elderly voices, which persisted in most models despite chain-of-thought prompting. While explicit reasoning successfully eliminated gender bias, the impact of emotion was not detected due to poor recognition performance. These results demonstrate that audio LLMs are susceptible to making clinical decisions based on a patient's voice characteristics rather than medical evidence, a flaw that risks perpetuating healthcare disparities. We conclude that bias-aware architectures are essential and urgently needed before the clinical deployment of these models.

Egocentric vision systems aim to understand the spatial surroundings and the wearer's behavior inside it, including motions, activities, and interactions. We argue that egocentric systems must additionally detect physiological states to capture a person's attention and situational responses, which are critical for context-aware behavior modeling. In this paper, we propose egoPPG, a novel vision task for egocentric systems to recover a person's cardiac activity to aid downstream vision tasks. We introduce PulseFormer, a method to extract heart rate as a key indicator of physiological state from the eye tracking cameras on unmodified egocentric vision systems. PulseFormer continuously estimates the photoplethysmogram (PPG) from areas around the eyes and fuses motion cues from the headset's inertial measurement unit to track HR values. We demonstrate egoPPG's downstream benefit for a key task on EgoExo4D, an existing egocentric dataset for which we find PulseFormer's estimates of HR to improve proficiency estimation by 14%. To train and validate PulseFormer, we collected a dataset of 13+ hours of eye tracking videos from Project Aria and contact-based PPG signals as well as an electrocardiogram (ECG) for ground-truth HR values. Similar to EgoExo4D, 25 participants performed diverse everyday activities such as office work, cooking, dancing, and exercising, which induced significant natural motion and HR variation (44-164 bpm). Our model robustly estimates HR (MAE=7.67 bpm) and captures patterns (r=0.85). Our results show how egocentric systems may unify environmental and physiological tracking to better understand users and that egoPPG as a complementary task provides meaningful augmentations for existing datasets and tasks. We release our code, dataset, and HR augmentations for EgoExo4D to inspire research on physiology-aware egocentric tasks.

In critical decision-making scenarios, optimizing accuracy can lead to a biased classifier, hence past work recommends enforcing group-based fairness metrics in addition to maximizing accuracy. However, doing so exposes the classifier to another kind of bias called infra-marginality. This refers to individual-level bias where some individuals/subgroups can be worse off than under simply optimizing for accuracy. For instance, a classifier implementing race-based parity may significantly disadvantage women of the advantaged race. To quantify this bias, we propose a general notion of eta-infra-marginality that can be used to evaluate the extent of this bias. We prove theoretically that, unlike other fairness metrics, infra-marginality does not have a trade-off with accuracy: high accuracy directly leads to low infra-marginality. This observation is confirmed through empirical analysis on multiple simulated and real-world datasets. Further, we find that maximizing group fairness often increases infra-marginality, suggesting the consideration of both group-level fairness and individual-level infra-marginality. However, measuring infra-marginality requires knowledge of the true distribution of individual-level outcomes correctly and explicitly. We propose a practical method to measure infra-marginality, and a simple algorithm to maximize group-wise accuracy and avoid infra-marginality.

Photoplethysmography (PPG) is a widely adopted, non-invasive technique for monitoring cardiovascular health and physiological parameters in both consumer and clinical settings. While motion artifacts in dynamic environments have been extensively studied, suboptimal skin-sensor contact in sedentary conditions - a critical yet underexplored issue - can distort PPG waveform morphology, leading to the loss or misalignment of key features and compromising sensing accuracy. In this work, we propose CP-PPG, a novel framework that transforms Contact Pressure-distorted PPG signals into high-fidelity waveforms with ideal morphology. CP-PPG integrates a custom data collection protocol, a carefully designed signal processing pipeline, and a novel deep adversarial model trained with a custom PPG-aware loss function. We validated CP-PPG through comprehensive evaluations, including 1) morphology transformation performance on our self-collected dataset, 2) downstream physiological monitoring performance on public datasets, and 3) in-the-wild study. Extensive experiments demonstrate substantial and consistent improvements in signal fidelity (Mean Absolute Error: 0.09, 40% improvement over the original signal) as well as downstream performance across all evaluations in Heart Rate (HR), Heart Rate Variability (HRV), Respiration Rate (RR), and Blood Pressure (BP) estimation (on average, 21% improvement in HR; 41-46% in HRV; 6% in RR; and 4-5% in BP). These findings highlight the critical importance of addressing skin-sensor contact issues to enhance the reliability and effectiveness of PPG-based physiological monitoring. CP-PPG thus holds significant potential to improve the accuracy of wearable health technologies in clinical and consumer applications.

Effective earthquake risk reduction relies on accurate site-specific evaluations. This requires models that can represent the influence of local site conditions on ground motion characteristics. In this context, data driven approaches that learn site controlled signatures from recorded ground motions offer a promising direction. We address strong ground motion generation from time-domain accelerometer records and introduce the TimesNet-Gen, a time-domain conditional generator. The approach uses a station specific latent bottleneck. We evaluate generation by comparing HVSR curves and fundamental site-frequency f_0 distributions between real and generated records per station, and summarize station specificity with a score based on the f_0 distribution confusion matrices. TimesNet-Gen achieves strong station-wise alignment and compares favorably with a spectrogram-based conditional VAE baseline for site-specific strong motion synthesis. Our codes are available via https://github.com/brsylmz23/TimesNet-Gen.

Social interactions are fundamental to well-being, yet automatically detecting them in daily life-particularly using wearables-remains underexplored. Most existing systems are evaluated in controlled settings, focus primarily on in-person interactions, or rely on restrictive assumptions (e.g., requiring multiple speakers within fixed temporal windows), limiting generalizability to real-world use. We present an on-watch interaction detection system designed to capture diverse interactions in naturalistic settings. A core component is a foreground speech detector trained on a public dataset. Evaluated on over 100,000 labeled foreground speech and background sound instances, the detector achieves a balanced accuracy of 85.51%, outperforming prior work by 5.11%. We evaluated the system in a real-world deployment (N=38), with over 900 hours of total smartwatch wear time. The system detected 1,691 interactions, 77.28% were confirmed via participant self-report, with durations ranging from under one minute to over one hour. Among correct detections, 81.45% were in-person, 15.7% virtual, and 1.85% hybrid. Leveraging participant-labeled data, we further developed a multimodal model achieving a balanced accuracy of 90.36% and a sensitivity of 91.17% on 33,698 labeled 15-second windows. These results demonstrate the feasibility of real-world interaction sensing and open the door to adaptive, context-aware systems responding to users' dynamic social environments.

As LLMs are increasingly integrated into user-facing applications, addressing biases that perpetuate societal inequalities is crucial. While much work has gone into measuring or mitigating biases in these models, fewer studies have investigated their origins. Therefore, this study examines the correlation between gender-occupation bias in pre-training data and their manifestation in LLMs, focusing on the Dolma dataset and the OLMo model. Using zero-shot prompting and token co-occurrence analyses, we explore how biases in training data influence model outputs. Our findings reveal that biases present in pre-training data are amplified in model outputs. The study also examines the effects of prompt types, hyperparameters, and instruction-tuning on bias expression, finding instruction-tuning partially alleviating representational bias while still maintaining overall stereotypical gender associations, whereas hyperparameters and prompting variation have a lesser effect on bias expression. Our research traces bias throughout the LLM development pipeline and underscores the importance of mitigating bias at the pretraining stage.

Many people have flipped coins but few have stopped to ponder the statistical and physical intricacies of the process. We collected 350{,}757 coin flips to test the counterintuitive prediction from a physics model of human coin tossing developed by Diaconis, Holmes, and Montgomery (DHM; 2007). The model asserts that when people flip an ordinary coin, it tends to land on the same side it started -- DHM estimated the probability of a same-side outcome to be about 51\%. Our data lend strong support to this precise prediction: the coins landed on the same side more often than not, Pr(same side) = 0.508, 95\% credible interval (CI) [0.506, 0.509], BF_{same-side bias} = 2359. Furthermore, the data revealed considerable between-people variation in the degree of this same-side bias. Our data also confirmed the generic prediction that when people flip an ordinary coin -- with the initial side-up randomly determined -- it is equally likely to land heads or tails: Pr(heads) = 0.500, 95\% CI [0.498, 0.502], BF_{heads-tails bias} = 0.182. Furthermore, this lack of heads-tails bias does not appear to vary across coins. Additional analyses revealed that the within-people same-side bias decreased as more coins were flipped, an effect that is consistent with the possibility that practice makes people flip coins in a less wobbly fashion. Our data therefore provide strong evidence that when some (but not all) people flip a fair coin, it tends to land on the same side it started.

LLM-as-a-Judge has emerged as a promising alternative to human evaluators across various tasks, yet inherent biases - particularly position bias, the tendency to favor solutions based on their position within the prompt - compromise its reliability. This exploratory study evaluates position bias in LLM judges across pairwise and list-wise comparison settings, introducing three metrics: repetition stability, position consistency, and preference fairness. Our experiments, involving 15 LLM judges across MTBench and DevBench with 22 tasks and approximately 40 solution-generating models, result in over 150,000 evaluation instances. We identify Judge-Level, Candidate-Level, and Task-Level factors contributing to bias. The findings confirm that position bias is not due to random chance and varies significantly across judges and tasks. While position bias is weakly influenced by the length of prompt components, it is strongly affected by the quality gap between solutions. Our agreement and disagreement analysis among judges further provides insights into the distribution of judging difficulty across the dataset, and highlights the potential for dataset modifications.

We aim to learn a joint representation between inertial measurement unit (IMU) signals and 2D pose sequences extracted from video, enabling accurate cross-modal retrieval, temporal synchronization, subject and body-part localization, and action recognition. To this end, we introduce MoBind, a hierarchical contrastive learning framework designed to address three challenges: (1) filtering out irrelevant visual background, (2) modeling structured multi-sensor IMU configurations, and (3) achieving fine-grained, sub-second temporal alignment. To isolate motion-relevant cues, MoBind aligns IMU signals with skeletal motion sequences rather than raw pixels. We further decompose full-body motion into local body-part trajectories, pairing each with its corresponding IMU to enable semantically grounded multi-sensor alignment. To capture detailed temporal correspondence, MoBind employs a hierarchical contrastive strategy that first aligns token-level temporal segments, then fuses local (body-part) alignment with global (body-wide) motion aggregation. Evaluated on mRi, TotalCapture, and EgoHumans, MoBind consistently outperforms strong baselines across all four tasks, demonstrating robust fine-grained temporal alignment while preserving coarse semantic consistency across modalities. Code is available at https://github.com/bbvisual/ MoBind.

Detecting speech from biosignals is gaining increasing attention due to the potential to develop human-computer interfaces that are noise-robust, privacy-preserving, and scalable for both clinical applications and daily use. However, most existing approaches remain limited by insufficient wearability and the lack of edge-processing capabilities, which are essential for minimally obtrusive, responsive, and private assistive technologies. In this work, we present SilentWear, a fully wearable, textile-based neck interface for EMG signal acquisition and processing. Powered by BioGAP-Ultra, the system enables end-to-end data acquisition from 14 differential channels and on-device speech recognition. SilentWear is coupled with SpeechNet, a lightweight 15k-parameter CNN architecture specifically tailored for EMG-based speech decoding, achieving an average cross-validated accuracy of 84.8pm4.6% and 77.5pm6.6% for vocalized and silent speech, respectively, over eight representative human-machine interaction commands collected over multiple days. We evaluate robustness to repositioning induced by multi-day use. In an inter-session setting, the system achieves average accuracies of 71.1pm8.3% and 59.3\pm2.2% for vocalized and silent speech, respectively. To mitigate performance degradation due to repositioning, we propose an incremental fine-tuning strategy, demonstrating more than 10% accuracy recovery with less than 10 minutes of additional user data. Finally, we demonstrate end-to-end real-time on-device speech recognition on a commercial multi-core microcontroller unit (MCU), achieving an energy consumption of 63.9μJ per inference with a latency of 2.47 ms. With a total power consumption of 20.5mW for acquisition, inference, and wireless transmission of results, SilentWear enables continuous operation for more than 27 hours.

Modern LLM agents combine long-term memory for personalization with tool-calling interfaces for taking actions in the world -- a combination underpinning contemporary production systems. We study a previously unexamined failure of this combination: when personality-driven biases stored in memory (cost-consciousness, impatience, risk tolerance, etc.) silently affect tool calls in contexts where they are not applicable. We call this memory-induced tool-drift and operationalize it through MEMDRIFT, a benchmark of 105 scenarios spanning five bias dimensions and seven professional domains, generated through an automated adversarial pipeline. Across seven frontier models -- including those with extended reasoning -- biased memories raise deflection scores (a judge-scored measure of parameter deviation from unbiased baselines) by up to +3.6 points on a 1--5 scale. Tool-drift persists when memory management is handled by three production memory architectures. The phenomenon affects real-world tools: scanning 6{,}062 tools across 288 verified MCP servers, we flag 608 with susceptible parameters and confirm tool-drift on a validated subset. Mechanistically, biased memories act as implicit steering vectors, pushing activations along the same latent directions as explicit behavioral instructions. They also redistribute attention from task-relevant context toward memory entries with surface-level keyword overlap to the target parameter. Standard defenses -- prompt-based relevance instructions and memory filters -- reduce drift but do not eliminate it. As agents take increasingly consequential actions on a user's behalf, memory-induced tool-drift represents a systematic vulnerability that current safeguards do not address, motivating dedicated defenses at the intersection of memory management and tool-call generation.

In recent years, social media users have spent significant amounts of time on short-form video platforms. As a result, established platforms in other domains, such as e-commerce, have begun introducing short-form video content to engage users and increase their time spent on the platform. The success of these experiences is due not only to the content itself but also to a unique UI innovation: instead of offering users a list of choices to click, platforms actively recommend content for users to watch one at a time. This creates new challenges for recommender systems, especially when launching a new video experience. Beyond the limited interaction data, immersive feed experiences introduce stronger position bias due to the UI and duration bias when optimizing for watch-time, as models tend to favor shorter videos. These issues, together with the feedback loop inherent in recommender systems, make it difficult to build effective solutions. In this paper, we highlight the challenges faced when introducing a new short-form video experience and present our experience showing that, even with sufficient video interaction data, it can be more beneficial to leverage a video retrieval system using a fine-tuned multimodal vision-language model to overcome these challenges. This approach demonstrated greater effectiveness compared to conventional supervised learning methods in online experiments conducted on our e-commerce platform.

Recommendation systems (RS) aim to provide personalized content, but they face a challenge in unbiased learning due to selection bias, where users only interact with items they prefer. This bias leads to a distorted representation of user preferences, which hinders the accuracy and fairness of recommendations. To address the issue, various methods such as error imputation based, inverse propensity scoring, and doubly robust techniques have been developed. Despite the progress, from the structural causal model perspective, previous debiasing methods in RS assume the independence of the exogenous variables. In this paper, we release this assumption and propose a learning algorithm based on likelihood maximization to learn a prediction model. We first discuss the correlation and difference between unmeasured confounding and our scenario, then we propose a unified method that effectively handles latent exogenous variables. Specifically, our method models the data generation process with latent exogenous variables under mild normality assumptions. We then develop a Monte Carlo algorithm to numerically estimate the likelihood function. Extensive experiments on synthetic datasets and three real-world datasets demonstrate the effectiveness of our proposed method. The code is at https://github.com/WallaceSUI/kdd25-background-variable.

Falls are significant and often fatal for vulnerable populations such as the elderly. Previous works have addressed the detection of falls by relying on data capture by a single sensor, images or accelerometers. In this work, we rely on multimodal descriptors extracted from videos captured by egocentric cameras. Our proposed method includes a late decision fusion layer that builds on top of the extracted descriptors. Furthermore, we collect a new dataset on which we assess our proposed approach. We believe this is the first public dataset of its kind. The dataset comprises 10,948 video samples by 14 subjects. We conducted ablation experiments to assess the performance of individual feature extractors, fusion of visual information, and fusion of both visual and audio information. Moreover, we experimented with internal and external cross-validation. Our results demonstrate that the fusion of audio and visual information through late decision fusion improves detection performance, making it a promising tool for fall prevention and mitigation.

A transhumeral prosthesis restores missing anatomical segments below the shoulder, including the hand. Active prostheses utilize real-valued, continuous sensor data to recognize patient target poses, or goals, and proactively move the artificial limb. Previous studies have examined how well the data collected in stationary poses, without considering the time steps, can help discriminate the goals. In this case study paper, we focus on using time series data from surface electromyography electrodes and kinematic sensors to sequentially recognize patients' goals. Our approach involves transforming the data into discrete events and training an existing process mining-based goal recognition system. Results from data collected in a virtual reality setting with ten subjects demonstrate the effectiveness of our proposed goal recognition approach, which achieves significantly better precision and recall than the state-of-the-art machine learning techniques and is less confident when wrong, which is beneficial when approximating smoother movements of prostheses.

LLMs can exhibit age biases, resulting in unequal treatment of individuals across age groups. While much research has addressed racial and gender biases, age bias remains little explored. The scarcity of instruction-tuning and preference datasets for age bias hampers its detection and measurement, and existing fine-tuning methods seldom address age-related fairness. In this paper, we construct age bias preference datasets and instruction-tuning datasets for RLHF. We introduce ARG, an age fairness reward to reduce differences in the response quality of LLMs across different age groups. Extensive experiments demonstrate that this reward significantly improves response accuracy and reduces performance disparities across age groups. Our source code and datasets are available at the anonymous https://anonymous.4open.science/r/FairRLHF-D445/readme.md{link}.

Audio-Visual Source Localization (AVSL) aims to localize the source of sound within a video. In this paper, we identify a significant issue in existing benchmarks: the sounding objects are often easily recognized based solely on visual cues, which we refer to as visual bias. Such biases hinder these benchmarks from effectively evaluating AVSL models. To further validate our hypothesis regarding visual biases, we examine two representative AVSL benchmarks, VGG-SS and EpicSounding-Object, where the vision-only models outperform all audiovisual baselines. Our findings suggest that existing AVSL benchmarks need further refinement to facilitate audio-visual learning.

Accurate motion estimation for tracking deformable tissues in echocardiography is essential for precise cardiac function measurements. While traditional methods like block matching or optical flow struggle with intricate cardiac motion, modern point tracking approaches remain largely underexplored in this domain. This work investigates the potential of state-of-the-art (SOTA) point tracking methods for ultrasound, with a focus on echocardiography. Although these novel approaches demonstrate strong performance in general videos, their effectiveness and generalizability in echocardiography remain limited. By analyzing cardiac motion throughout the heart cycle in real B-mode ultrasound videos, we identify that a directional motion bias across different views is affecting the existing training strategies. To mitigate this, we refine the training procedure and incorporate a set of tailored augmentations to reduce the bias and enhance tracking robustness and generalization through impartial cardiac motion. We also propose a lightweight network leveraging multi-scale cost volumes from spatial context alone to challenge the advanced spatiotemporal point tracking models. Experiments demonstrate that fine-tuning with our strategies significantly improves models' performances over their baselines, even for out-of-distribution (OOD) cases. For instance, EchoTracker boosts overall position accuracy by 60.7% and reduces median trajectory error by 61.5% across heart cycle phases. Interestingly, several point tracking models fail to outperform our proposed simple model in terms of tracking accuracy and generalization, reflecting their limitations when applied to echocardiography. Nevertheless, clinical evaluation reveals that these methods improve GLS measurements, aligning more closely with expert-validated, semi-automated tools and thus demonstrating better reproducibility in real-world applications.

This abstract explores an RNN-based approach to online handwritten recognition problem. Our method uses data from an accelerometer and a gyroscope mounted on a handheld pen-like device to train and run a character pre-diction model. We have built a dataset of timestamped gyroscope and accelerometer data gathered during the manual process of handwriting Latin characters, labeled with the character being written; in total, the dataset con-sists of 1500 gyroscope and accelerometer data sequenc-es for 8 characters of the Latin alphabet from 6 different people, and 20 characters, each 1500 samples from Georgian alphabet from 5 different people. with each sequence containing the gyroscope and accelerometer data captured during the writing of a particular character sampled once every 10ms. We train an RNN-based neural network architecture on this dataset to predict the character being written. The model is optimized with categorical cross-entropy loss and RMSprop optimizer and achieves high accuracy on test data.

In video action recognition, shortcut static features can interfere with the learning of motion features, resulting in poor out-of-distribution (OOD) generalization. The video background is clearly a source of static bias, but the video foreground, such as the clothing of the actor, can also provide static bias. In this paper, we empirically verify the existence of foreground static bias by creating test videos with conflicting signals from the static and moving portions of the video. To tackle this issue, we propose a simple yet effective technique, StillMix, to learn robust action representations. Specifically, StillMix identifies bias-inducing video frames using a 2D reference network and mixes them with videos for training, serving as effective bias suppression even when we cannot explicitly extract the source of bias within each video frame or enumerate types of bias. Finally, to precisely evaluate static bias, we synthesize two new benchmarks, SCUBA for static cues in the background, and SCUFO for static cues in the foreground. With extensive experiments, we demonstrate that StillMix mitigates both types of static bias and improves video representations for downstream applications.

Effective rehabilitation assessment is essential for monitoring patient progress, particularly in home-based settings. Existing systems often face challenges such as data imbalance and difficulty detecting subtle movement errors. This paper introduces Error-Guided Pose Augmentation (EGPA), a method that generates synthetic skeleton data by simulating clinically relevant movement mistakes. Unlike standard augmentation techniques, EGPA targets biomechanical errors observed in rehabilitation. Combined with an attention-based graph convolutional network, EGPA improves performance across multiple evaluation metrics. Experiments demonstrate reductions in mean absolute error of up to 27.6 percent and gains in error classification accuracy of 45.8 percent. Attention visualizations show that the model learns to focus on clinically significant joints and movement phases, enhancing both accuracy and interpretability. EGPA offers a promising approach for improving automated movement quality assessment in both clinical and home-based rehabilitation contexts.

Hands are the primary means through which humans interact with the world. Reliable and always-available hand pose inference could yield new and intuitive control schemes for human-computer interactions, particularly in virtual and augmented reality. Computer vision is effective but requires one or multiple cameras and can struggle with occlusions, limited field of view, and poor lighting. Wearable wrist-based surface electromyography (sEMG) presents a promising alternative as an always-available modality sensing muscle activities that drive hand motion. However, sEMG signals are strongly dependent on user anatomy and sensor placement, and existing sEMG models have required hundreds of users and device placements to effectively generalize. To facilitate progress on sEMG pose inference, we introduce the emg2pose benchmark, the largest publicly available dataset of high-quality hand pose labels and wrist sEMG recordings. emg2pose contains 2kHz, 16 channel sEMG and pose labels from a 26-camera motion capture rig for 193 users, 370 hours, and 29 stages with diverse gestures - a scale comparable to vision-based hand pose datasets. We provide competitive baselines and challenging tasks evaluating real-world generalization scenarios: held-out users, sensor placements, and stages. emg2pose provides the machine learning community a platform for exploring complex generalization problems, holding potential to significantly enhance the development of sEMG-based human-computer interactions.

Unintended bias in Machine Learning can manifest as systemic differences in performance for different demographic groups, potentially compounding existing challenges to fairness in society at large. In this paper, we introduce a suite of threshold-agnostic metrics that provide a nuanced view of this unintended bias, by considering the various ways that a classifier's score distribution can vary across designated groups. We also introduce a large new test set of online comments with crowd-sourced annotations for identity references. We use this to show how our metrics can be used to find new and potentially subtle unintended bias in existing public models.

Sensitive inferences and user re-identification are major threats to privacy when raw sensor data from wearable or portable devices are shared with cloud-assisted applications. To mitigate these threats, we propose mechanisms to transform sensor data before sharing them with applications running on users' devices. These transformations aim at eliminating patterns that can be used for user re-identification or for inferring potentially sensitive activities, while introducing a minor utility loss for the target application (or task). We show that, on gesture and activity recognition tasks, we can prevent inference of potentially sensitive activities while keeping the reduction in recognition accuracy of non-sensitive activities to less than 5 percentage points. We also show that we can reduce the accuracy of user re-identification and of the potential inference of gender to the level of a random guess, while keeping the accuracy of activity recognition comparable to that obtained on the original data.

A typical pipeline for multi-object tracking (MOT) is to use a detector for object localization, and following re-identification (re-ID) for object association. This pipeline is partially motivated by recent progress in both object detection and re-ID, and partially motivated by biases in existing tracking datasets, where most objects tend to have distinguishing appearance and re-ID models are sufficient for establishing associations. In response to such bias, we would like to re-emphasize that methods for multi-object tracking should also work when object appearance is not sufficiently discriminative. To this end, we propose a large-scale dataset for multi-human tracking, where humans have similar appearance, diverse motion and extreme articulation. As the dataset contains mostly group dancing videos, we name it "DanceTrack". We expect DanceTrack to provide a better platform to develop more MOT algorithms that rely less on visual discrimination and depend more on motion analysis. We benchmark several state-of-the-art trackers on our dataset and observe a significant performance drop on DanceTrack when compared against existing benchmarks. The dataset, project code and competition server are released at: https://github.com/DanceTrack.

Best-of-N (BoN) Average Displacement Error (ADE)/ Final Displacement Error (FDE) is the most used metric for evaluating trajectory prediction models. Yet, the BoN does not quantify the whole generated samples, resulting in an incomplete view of the model's prediction quality and performance. We propose a new metric, Average Mahalanobis Distance (AMD) to tackle this issue. AMD is a metric that quantifies how close the whole generated samples are to the ground truth. We also introduce the Average Maximum Eigenvalue (AMV) metric that quantifies the overall spread of the predictions. Our metrics are validated empirically by showing that the ADE/FDE is not sensitive to distribution shifts, giving a biased sense of accuracy, unlike the AMD/AMV metrics. We introduce the usage of Implicit Maximum Likelihood Estimation (IMLE) as a replacement for traditional generative models to train our model, Social-Implicit. IMLE training mechanism aligns with AMD/AMV objective of predicting trajectories that are close to the ground truth with a tight spread. Social-Implicit is a memory efficient deep model with only 5.8K parameters that runs in real time of about 580Hz and achieves competitive results. Interactive demo of the problem can be seen at https://www.abduallahmohamed.com/social-implicit-amdamv-adefde-demo . Code is available at https://github.com/abduallahmohamed/Social-Implicit .

The way the media presents events can significantly affect public perception, which in turn can alter people's beliefs and views. Media bias describes a one-sided or polarizing perspective on a topic. This article summarizes the research on computational methods to detect media bias by systematically reviewing 3140 research papers published between 2019 and 2022. To structure our review and support a mutual understanding of bias across research domains, we introduce the Media Bias Taxonomy, which provides a coherent overview of the current state of research on media bias from different perspectives. We show that media bias detection is a highly active research field, in which transformer-based classification approaches have led to significant improvements in recent years. These improvements include higher classification accuracy and the ability to detect more fine-granular types of bias. However, we have identified a lack of interdisciplinarity in existing projects, and a need for more awareness of the various types of media bias to support methodologically thorough performance evaluations of media bias detection systems. Concluding from our analysis, we see the integration of recent machine learning advancements with reliable and diverse bias assessment strategies from other research areas as the most promising area for future research contributions in the field.

We use tools from geometric statistics to analyze the usual estimation procedure of a template shape. This applies to shapes from landmarks, curves, surfaces, images etc. We demonstrate the asymptotic bias of the template shape estimation using the stratified geometry of the shape space. We give a Taylor expansion of the bias with respect to a parameter sigma describing the measurement error on the data. We propose two bootstrap procedures that quantify the bias and correct it, if needed. They are applicable for any type of shape data. We give a rule of thumb to provide intuition on whether the bias has to be corrected. This exhibits the parameters that control the bias' magnitude. We illustrate our results on simulated and real shape data.

Gait disorders are commonly observed in older adults, who frequently experience various issues related to walking. Additionally, researchers and clinicians extensively investigate mobility related to gait in typically and atypically developing children, athletes, and individuals with orthopedic and neurological disorders. Effective gait analysis enables the understanding of the causal mechanisms of mobility and balance control of patients, the development of tailored treatment plans to improve mobility, the reduction of fall risk, and the tracking of rehabilitation progress. However, analyzing gait data is a complex task due to the multivariate nature of the data, the large volume of information to be interpreted, and the technical skills required. Existing tools for gait analysis are often limited to specific patient groups (e.g., cerebral palsy), only handle a specific subset of tasks in the entire workflow, and are not openly accessible. To address these shortcomings, we conducted a requirements assessment with gait practitioners (e.g., researchers, clinicians) via surveys and identified key components of the workflow, including (1) data processing and (2) data analysis and visualization. Based on the findings, we designed VIGMA, an open-access visual analytics framework integrated with computational notebooks and a Python library, to meet the identified requirements. Notably, the framework supports analytical capabilities for assessing disease progression and for comparing multiple patient groups. We validated the framework through usage scenarios with experts specializing in gait and mobility rehabilitation. VIGMA is available at https://github.com/komar41/VIGMA.

Transfer learning is beneficial by allowing the expressive features of models pretrained on large-scale datasets to be finetuned for the target task of smaller, more domain-specific datasets. However, there is a concern that these pretrained models may come with their own biases which would propagate into the finetuned model. In this work, we investigate bias when conceptualized as both spurious correlations between the target task and a sensitive attribute as well as underrepresentation of a particular group in the dataset. Under both notions of bias, we find that (1) models finetuned on top of pretrained models can indeed inherit their biases, but (2) this bias can be corrected for through relatively minor interventions to the finetuning dataset, and often with a negligible impact to performance. Our findings imply that careful curation of the finetuning dataset is important for reducing biases on a downstream task, and doing so can even compensate for bias in the pretrained model.

This study presents an automated lameness detection system that uses deep-learning image processing techniques to extract multiple locomotion traits associated with lameness. Using the T-LEAP pose estimation model, the motion of nine keypoints was extracted from videos of walking cows. The videos were recorded outdoors, with varying illumination conditions, and T-LEAP extracted 99.6% of correct keypoints. The trajectories of the keypoints were then used to compute six locomotion traits: back posture measurement, head bobbing, tracking distance, stride length, stance duration, and swing duration. The three most important traits were back posture measurement, head bobbing, and tracking distance. For the ground truth, we showed that a thoughtful merging of the scores of the observers could improve intra-observer reliability and agreement. We showed that including multiple locomotion traits improves the classification accuracy from 76.6% with only one trait to 79.9% with the three most important traits and to 80.1% with all six locomotion traits.

Deep learning's growing prevalence has driven its widespread use in healthcare, where AI and sensor advancements enhance diagnosis, treatment, and monitoring. In mobile health, AI-powered tools enable early diagnosis and continuous monitoring of conditions like stress. Wearable technologies and multimodal physiological data have made stress detection increasingly viable, but model efficacy depends on data quality, quantity, and modality. This study develops transformer models for stress detection using the WESAD dataset, training on electrocardiograms (ECG), electrodermal activity (EDA), electromyography (EMG), respiration rate (RESP), temperature (TEMP), and 3-axis accelerometer (ACC) signals. The results demonstrate the effectiveness of single-modality transformers in analyzing physiological signals, achieving state-of-the-art performance with accuracy, precision and recall values in the range of 99.73% to 99.95% for stress detection. Furthermore, this study explores cross-modal performance and also explains the same using 2D visualization of the learned embedding space and quantitative analysis based on data variance. Despite the large body of work on stress detection and monitoring, the robustness and generalization of these models across different modalities has not been explored. This research represents one of the initial efforts to interpret embedding spaces for stress detection, providing valuable information on cross-modal performance.

Various design settings for in-context learning (ICL), such as the choice and order of the in-context examples, can bias a model toward a particular prediction without being reflective of an understanding of the task. While many studies discuss these design choices, there have been few systematic investigations into categorizing them and mitigating their impact. In this work, we define a typology for three types of label biases in ICL for text classification: vanilla-label bias, context-label bias, and domain-label bias (which we conceptualize and detect for the first time). Our analysis demonstrates that prior label bias calibration methods fall short of addressing all three types of biases. Specifically, domain-label bias restricts LLMs to random-level performance on many tasks regardless of the choice of in-context examples. To mitigate the effect of these biases, we propose a simple bias calibration method that estimates a language model's label bias using random in-domain words from the task corpus. After controlling for this estimated bias when making predictions, our novel domain-context calibration significantly improves the ICL performance of GPT-J and GPT-3 on a wide range of tasks. The gain is substantial on tasks with large domain-label bias (up to 37% in Macro-F1). Furthermore, our results generalize to models with different scales, pretraining methods, and manually-designed task instructions, showing the prevalence of label biases in ICL.

Purpose. Handwriting is one of the most frequently occurring patterns in everyday life and with it come challenging applications such as handwriting recognition (HWR), writer identification, and signature verification. In contrast to offline HWR that only uses spatial information (i.e., images), online HWR (OnHWR) uses richer spatio-temporal information (i.e., trajectory data or inertial data). While there exist many offline HWR datasets, there is only little data available for the development of OnHWR methods on paper as it requires hardware-integrated pens. Methods. This paper presents data and benchmark models for real-time sequence-to-sequence (seq2seq) learning and single character-based recognition. Our data is recorded by a sensor-enhanced ballpoint pen, yielding sensor data streams from triaxial accelerometers, a gyroscope, a magnetometer and a force sensor at 100 Hz. We propose a variety of datasets including equations and words for both the writer-dependent and writer-independent tasks. Our datasets allow a comparison between classical OnHWR on tablets and on paper with sensor-enhanced pens. We provide an evaluation benchmark for seq2seq and single character-based HWR using recurrent and temporal convolutional networks and Transformers combined with a connectionist temporal classification (CTC) loss and cross-entropy (CE) losses. Results. Our convolutional network combined with BiLSTMs outperforms Transformer-based architectures, is on par with InceptionTime for sequence-based classification tasks, and yields better results compared to 28 state-of-the-art techniques. Time-series augmentation methods improve the sequence-based task, and we show that CE variants can improve the single classification task.

Studies of bias in LLM-as-judge systems typically build synthetic corpora by prompting an LLM to generate a hallucinated answer to pair with a factual one, then presenting both to a judge. We report a case in which this generation step silently failed, and use it to argue that the failure mode is structural rather than incidental. In a multilingual (Turkish/English) faithfulness-judgment corpus, a decoding-budget parameter shared between judging and generation calls truncated one producer's hallucinated answers to a few words. The resulting items produced a large, statistically robust effect: a 32-point cross-lingual collapse in one judge's selection accuracy, replicated from N=50 to N=500, explained by a three-layer mechanistic account, and confirmed by a controlled producer-swap experiment, none of which was real. The effect vanished to ceiling once the shared parameter was corrected, and only manual reading of the raw generations, not any aggregate statistical check, exposed the fault. A second measured bias (Markdown-formatting preference) was not fabricated but distorted by the same fault, its magnitude and in one case its sign shifting with stimulus length, a mode aggregate metrics cannot distinguish from the first. We frame the underlying vulnerability using the test oracle problem: corpora whose negative examples are LLM-generated carry no mechanical way to verify item integrity, while corpora built by deterministic perturbation of a gold answer carry an item-level oracle for free. A positive control supports this claim directly: an analogous fault injected into a minimal perturbation-based corpus is caught with 100% accuracy by a zero-cost, zero-human gold-to-negative string comparison. We close with a validation protocol, derived from our own case, for analysts working in the oracle-less regime that we argue describes most contemporary multilingual LLM-as-judge corpora.

Lower-Limb Fractures (LLF) are a major health concern for older adults, often leading to reduced mobility and prolonged recovery, potentially impairing daily activities and independence. During recovery, older adults frequently face social isolation and functional decline, complicating rehabilitation and adversely affecting physical and mental health. Multi-modal sensor platforms that continuously collect data and analyze it using machine-learning algorithms can remotely monitor this population and infer health outcomes. They can also alert clinicians to individuals at risk of isolation and decline. This paper presents a new publicly available multi-modal sensor dataset, MAISON-LLF, collected from older adults recovering from LLF in community settings. The dataset includes data from smartphone and smartwatch sensors, motion detectors, sleep-tracking mattresses, and clinical questionnaires on isolation and decline. The dataset was collected from ten older adults living alone at home for eight weeks each, totaling 560 days of 24-hour sensor data. For technical validation, supervised machine-learning and deep-learning models were developed using the sensor and clinical questionnaire data, providing a foundational comparison for the research community.

Blind individuals face persistent challenges in last-mile navigation, including locating entrances, identifying obstacles, and navigating complex or cluttered spaces. Although wearable cameras are increasingly used in assistive systems, there has been no systematic, vantage-focused comparison to guide their design. This paper addresses that gap through a two-part investigation. First, we surveyed ten experienced blind cane users, uncovering navigation strategies, pain points, and technology preferences. Participants stressed the importance of multi-sensory integration, destination-focused travel, and assistive tools that complement (rather than replace) the cane's tactile utility. Second, we conducted controlled data collection with a blind participant navigating five real-world environments using synchronized head- and cane-mounted cameras, isolating vantage placement as the primary variable. To assess how each vantage supports spatial perception, we evaluated SLAM performance (for localization and mapping) and NeRF-based 3D reconstruction (for downstream scene understanding). Head-mounted sensors delivered superior localization accuracy, while cane-mounted views offered broader ground-level coverage and richer environmental reconstructions. A combined (head+cane) configuration consistently outperformed both. These results highlight the complementary strengths of different sensor placements and offer actionable guidance for developing hybrid navigation aids that are perceptive, robust, and user-aligned.

AR smart glasses need continuous behavioral context to offer proactive assistance, yet their most practical always-on sensor, the head-mounted Inertial Measurement Unit (IMU), detects only motion primitives such as walking or standing. We push beyond motion primitives to behavioral-level recognition, defining five categories that balance AR application need with sensor observability. To this end, we construct a 160K-sample Ego4D dataset with a four-tier quality assurance framework spanning 8 activity scenarios, and propose HiT-HAR, a 703K-parameter hierarchical model that outperforms prior head-mounted IMU models on five-class action and eight-class scenario recognition. We further map the observability frontier of head-mounted IMU through per-class separability analysis, identifying which behavioral categories are reliably observable (Locomotion), which benefit from temporal context (Object Transfer, Task Operation), and where scenario-dependent signal overlap poses remaining challenges. Our results indicate that architectural choices exploiting temporal context and scenario structure outperform simply scaling model size. The code and dataset are publicly available at https://github.com/Harvard-AI-and-Robotics-Lab/HiT-HAR.

Survey data are self-reported data collected directly from respondents by a questionnaire or an interview and are commonly used in epidemiology. Such data are traditionally collected via a single mode (e.g. face-to-face interview alone), but use of mixed-mode designs (e.g. offering face-to-face interview or online survey) has become more common. This introduces two key challenges. First, individuals may respond differently to the same question depending on the mode; these differences due to measurement are known as 'mode effects'. Second, different individuals may participate via different modes; these differences in sample composition between modes are known as 'mode selection'. Where recognised, mode effects are often handled by straightforward approaches such as conditioning on survey mode. However, while reducing mode effects, this and other equivalent approaches may introduce collider bias in the presence of mode selection. The existence of mode effects and the consequences of na\"ive conditioning may be underappreciated in epidemiology. This paper offers a simple introduction to these challenges using directed acyclic graphs by exploring a range of possible data structures. We discuss the potential implications of using conditioning- or imputation-based approaches and outline the advantages of quantitative bias analyses for dealing with mode effects.

We present a lightweight and affordable motion capture method based on two smartwatches and a head-mounted camera. In contrast to the existing approaches that use six or more expert-level IMU devices, our approach is much more cost-effective and convenient. Our method can make wearable motion capture accessible to everyone everywhere, enabling 3D full-body motion capture in diverse environments. As a key idea to overcome the extreme sparsity and ambiguities of sensor inputs, we integrate 6D head poses obtained from the head-mounted cameras for motion estimation. To enable capture in expansive indoor and outdoor scenes, we propose an algorithm to track and update floor level changes to define head poses, coupled with a multi-stage Transformer-based regression module. We also introduce novel strategies leveraging visual cues of egocentric images to further enhance the motion capture quality while reducing ambiguities. We demonstrate the performance of our method on various challenging scenarios, including complex outdoor environments and everyday motions including object interactions and social interactions among multiple individuals.

Gender bias in machine translation (MT) is recognized as an issue that can harm people and society. And yet, advancements in the field rarely involve people, the final MT users, or inform how they might be impacted by biased technologies. Current evaluations are often restricted to automatic methods, which offer an opaque estimate of what the downstream impact of gender disparities might be. We conduct an extensive human-centered study to examine if and to what extent bias in MT brings harms with tangible costs, such as quality of service gaps across women and men. To this aim, we collect behavioral data from 90 participants, who post-edited MT outputs to ensure correct gender translation. Across multiple datasets, languages, and types of users, our study shows that feminine post-editing demands significantly more technical and temporal effort, also corresponding to higher financial costs. Existing bias measurements, however, fail to reflect the found disparities. Our findings advocate for human-centered approaches that can inform the societal impact of bias.

As AI systems built from multiple language-model agents become more common, they are increasingly used to make decisions together: discussing, negotiating, and acting on shared tasks. While individual agents may appear well-aligned when tested on their own, problems can arise from how they interact with one another. We introduce the Arbiter, an agent designed to monitor multi-agent conversations in real time and identify which participants may be behaving in misaligned ways. The Arbiter operates under a limited "inspection budget", meaning it must decide carefully how to use its resources. As it observes a conversation step by step, it can choose to wait, question a participant, examine internal information such as system prompts or reasoning traces, or log concerning behavior. At the end, it produces a report identifying the likely source of misalignment. We evaluate the Arbiter across five conversation conditions, ranging from risky financial advice model organisms to evaluation-aware and colluding agents, we test five tool configurations of increasing capability and two backbone models. We find that the Arbiter reliably detects misaligned agents well before the end of the conversation, with active inspection tools improving both detection accuracy and speed. Weight-induced misalignment proves hardest to detect, while instruction-induced misalignment is identified reliably even under passive observation. The logging tool exhibits a dual effect, improving recall at the cost of precision. These results suggest that continual, budget-aware monitoring can effectively catch misalignment, and that overseeing multi-agent systems may require treating the auditor as an active participant in the process. The code is available at https://github.com/aisilab/arbiter.

Joint contact forces govern implant longevity, cartilage health, and rehabilitation outcomes, shaping who develops osteoarthritis, who recovers well from joint replacement, and who benefits from biomechanical interventions. Yet they remain measurable only invasively, in a few dozen patients with instrumented implants. I present a physics-free pipeline to predict instantaneous 3D hip and knee contact forces from an uncalibrated monocular video: no markers, force plates, electromyography, subject-specific imaging, or musculoskeletal model. Parametric body meshes are recovered per frame, encoded as kinematic features, and decoded into forces by a transformer whose pose stream is adaptively modulated at every layer by body shape, joint, side, activity text, and self-supervised video tokens (V-JEPA 2), unifying hip and knee in a single model. Under leave-one-subject-out cross-validation across 26 patients and 25 activity categories from the in vivo OrthoLoad database, the pipeline matches the accuracy of subject-specific musculoskeletal simulations (0.32 pm 0.08 BW RMSE for hip; 0.23 pm 0.03 BW for knee) and resolves peak force changes smaller than those reported for gait retraining and osteoarthritis progression. Applied zero-shot to an independent instrumented cohort, it rivals or outperforms prior published methods. Even without curated activity labels, video features alone preserve accuracy and enable end-to-end inference on raw footage. Driven by the predictor, a generative motion prior produces biomechanically plausible variants with reduced peak loading, rediscovering strategies from the predictive simulation literature. This pipeline establishes uncalibrated monocular video as a viable modality for estimating joint loading, opening a path toward retrospective analysis of archived clinical recordings, primary-care screening, and at-home rehabilitation tracking.

A dangerous assumption that can be made from prior work on the bias transfer hypothesis (BTH) is that biases do not transfer from pre-trained large language models (LLMs) to adapted models. We invalidate this assumption by studying the BTH in causal models under prompt adaptations, as prompting is an extremely popular and accessible adaptation strategy used in real-world applications. In contrast to prior work, we find that biases can transfer through prompting and that popular prompt-based mitigation methods do not consistently prevent biases from transferring. Specifically, the correlation between intrinsic biases and those after prompt adaptation remain moderate to strong across demographics and tasks -- for example, gender (rho >= 0.94) in co-reference resolution, and age (rho >= 0.98) and religion (rho >= 0.69) in question answering. Further, we find that biases remain strongly correlated when varying few-shot composition parameters, such as sample size, stereotypical content, occupational distribution and representational balance (rho >= 0.90). We evaluate several prompt-based debiasing strategies and find that different approaches have distinct strengths, but none consistently reduce bias transfer across models, tasks or demographics. These results demonstrate that correcting bias, and potentially improving reasoning ability, in intrinsic models may prevent propagation of biases to downstream tasks.

As computer vision systems become more widely deployed, there is increasing concern from both the research community and the public that these systems are not only reproducing but amplifying harmful social biases. The phenomenon of bias amplification, which is the focus of this work, refers to models amplifying inherent training set biases at test time. Existing metrics measure bias amplification with respect to single annotated attributes (e.g., computer). However, several visual datasets consist of images with multiple attribute annotations. We show models can learn to exploit correlations with respect to multiple attributes (e.g., {computer, keyboard}), which are not accounted for by current metrics. In addition, we show current metrics can give the erroneous impression that minimal or no bias amplification has occurred as they involve aggregating over positive and negative values. Further, these metrics lack a clear desired value, making them difficult to interpret. To address these shortcomings, we propose a new metric: Multi-Attribute Bias Amplification. We validate our proposed metric through an analysis of gender bias amplification on the COCO and imSitu datasets. Finally, we benchmark bias mitigation methods using our proposed metric, suggesting possible avenues for future bias mitigation

We introduce and study the problem of detecting whether an agent is updating their prior beliefs given new evidence in an optimal way that is Bayesian, or whether they are biased towards their own prior. In our model, biased agents form posterior beliefs that are a convex combination of their prior and the Bayesian posterior, where the more biased an agent is, the closer their posterior is to the prior. Since we often cannot observe the agent's beliefs directly, we take an approach inspired by information design. Specifically, we measure an agent's bias by designing a signaling scheme and observing the actions they take in response to different signals, assuming that they are maximizing their own expected utility; our goal is to detect bias with a minimum number of signals. Our main results include a characterization of scenarios where a single signal suffices and a computationally efficient algorithm to compute optimal signaling schemes.

As a critical component of Wearable AI, IMU-based Human Activity Recognition (HAR) has attracted increasing attention from both academia and industry in recent years. Although HAR performance has improved considerably in specific scenarios, its generalization capability remains a key barrier to widespread real-world adoption. For example, domain shifts caused by variations in users, sensor positions, or environments can significantly decrease the performance in practice. As a result, in this survey, we explore the rapidly evolving field of IMU-based generalizable HAR, reviewing 229 research papers alongside 25 publicly available datasets to provide a broad and insightful overview. We first present the background and overall framework of IMU-based HAR tasks, as well as the generalization-oriented training settings. Then, we categorize representative methodologies from two perspectives: (i) model-centric approaches, including pre-training method, end-to-end method, and large language model (LLM)-based learning method; and (ii) data-centric approaches, including multi-modal learning and data augmentation techniques. In addition, we summarize widely used datasets in this field, as well as relevant tools and benchmarks. Building on these methodological advances, the broad applicability of IMU-based HAR is also reviewed and discussed. Finally, we discuss persistent challenges (e.g., data scarcity, efficient training, and reliable evaluation) and also outline future directions for HAR, including the adoption of foundation and large language models, physics-informed and context-aware reasoning, generative modeling, and resource-efficient training and inference. The complete list of this survey is available at https://github.com/rh20624/Awesome-IMU-Sensing, which will be updated continuously.

We identify first-mover bias -- path-dependent concentration of SHAP feature importance from sequential residual fitting in gradient boosting -- as a mechanistic contributor to attribution instability under multicollinearity. Scaling up a single model amplifies this effect: a Large Single Model matching our method's total tree count produces the poorest attribution reproducibility of any approach tested. We show that model independence largely neutralizes first-mover bias. Both DASH (Diversified Aggregation of SHAP) and simple seed-averaging (Stochastic Retrain) restore stability by breaking the sequential dependency chain. At rho=0.9, both achieve stability ~0.977, while Single Best degrades to 0.958 and LSM to 0.938. On Breast Cancer, DASH improves stability from 0.376 to 0.925 (+0.549), outperforming Stochastic Retrain by +0.063. Under nonlinear DGPs, the advantage emerges at rho>=0.7. DASH provides two diagnostic tools -- the Feature Stability Index and Importance-Stability Plot -- that detect first-mover bias without ground truth. A crossed ANOVA with formal F-statistics confirms the mechanism: DASH shifts variance from model-dominated (40.6%) to data-dominated (73.6%). Software at https://github.com/DrakeCaraker/dash-shap

Variances in ad impression outcomes across demographic groups are increasingly considered to be potentially indicative of algorithmic bias in personalized ads systems. While there are many definitions of fairness that could be applicable in the context of personalized systems, we present a framework which we call the Variance Reduction System (VRS) for achieving more equitable outcomes in Meta's ads systems. VRS seeks to achieve a distribution of impressions with respect to selected protected class (PC) attributes that more closely aligns the demographics of an ad's eligible audience (a function of advertiser targeting criteria) with the audience who sees that ad, in a privacy-preserving manner. We first define metrics to quantify fairness gaps in terms of ad impression variances with respect to PC attributes including gender and estimated race. We then present the VRS for re-ranking ads in an impression variance-aware manner. We evaluate VRS via extensive simulations over different parameter choices and study the effect of the VRS on the chosen fairness metric. We finally present online A/B testing results from applying VRS to Meta's ads systems, concluding with a discussion of future work. We have deployed the VRS to all users in the US for housing ads, resulting in significant improvement in our fairness metric. VRS is the first large-scale deployed framework for pursuing fairness for multiple PC attributes in online advertising.